Artos CS-327 Скачать руководство пользователя страница 114 | Manualshive

Страница: 114 / 133

Artos CS-327 Скачать руководство пользователя страница 114

114

Windows privileges for users

The CS327 software must have administrator privileges in Windows to work properly. If the user that
is currently logged in does not have administrator privileges, the CS327 software will automatically
log itself in to the user called Artos. The Artos user must always have administrator privileges. If
the CS327 software has to log itself in as the Artos user then only the CS327 software will have
administrator privileges, all other items in Windows will obey the privileges for the logged in user.

Machine

Software

Login

This is the log in screen for the machine software.

Configuring the software to require a log in

The control can be password protected. To do this a change in the <mtxconfig .xml> is required.

Use Windows File Explorer to locate the mtxcfg.xml file in C:\Program Files (x86)\Artos
Engineering\CS327GUI\Config. If the (x86) directory does not exist then go to C:\Program Files\Artos
Engineering\CS327GUI\Config.

It is suggested that you make a copy of the existing file before proceeding. Just click copy and paste to
copy it.

Right click on the original file and then click edit. If edit is not available from the drop down then
select open see the next step.

«
...
112
113
114
115
116
...
»

Содержание CS-327






































































































































Отзывы:

Нет отзывов