ARTEX A3-06-2824-1 Скачать руководство пользователя страница 9

Страница: 9 / 43

Y1-03-0272-1 Rev. C

A3-06-2824-1 Handheld Programmer Operations Manual

Company Confidential

Page 7

Hardware

The Handheld Programmer allows communication with any Artex 406 MHz ELT. It inverts

and raises the data signal from the ELT to an RS-232 signal level. This enables the ELT to

“

talk

”

to the Handheld Programmer for programming and diagnostic purposes.

2.1

Overview

The following subsections provide an overview of the Handheld Programmer hardware.

2.1.1

Connections

The Handheld Programmer is fitted with two connectors (Figure 2):

•

A quick connect/disconnect circular connector for connecting the programming

cables. This connector is push-on/pull-off type.

CAUTION

DO NOT TWIST THE CONNECTOR.

The built-in lock/release mechanism securely locks the mated connectors, while

allowing quick disconnection by simply pulling on the plug release collar. Molded-

in grooves prevent hand slippage when pulling on the connector.
Three cables are supplied with the Handheld Programmer to facilitate connection

to current Artex 406 MHz ELT models. The cables are:

▪

611-0112

–

For ME406 Series and ELT 345/1000

•

The ELT reader portion of the Handheld Programmer uses a Bayonet Neill-

Concelman (BNC) connector to allow connection of a 110-418 antenna or a direct-

connect coax cable. See 9.2 Optional Equipment.

Figure 2: Handheld Programmer Connectors (for reference only) Controls

Содержание A3-06-2824-1












































Результаты поиска

Содержание A3-06-2824-1

Отзывы:

Похожие инструкции для A3-06-2824-1

Бренды по названию

Популярные бренды

ARTEX A3-06-2824-1, Руководство по эксплуатации

Результаты поиска

Содержание A3-06-2824-1

Отзывы:

Похожие инструкции для A3-06-2824-1

Бренды по названию

Популярные бренды