ARTEX A3-06-2824-1 Скачать руководство пользователя страница 42

Страница: 42 / 43

Y1-03-0272-1 Rev. C

A3-06-2824-1 Handheld Programmer Operations Manual

Company Confidential

Page 40

10.

Troubleshooting

The following subsections provide troubleshooting and technical assistance information.

10.1

Trouble Shooting Guide

The following table provides user troubleshooting guidelines. For problems beyond the

scope of this guide, contact Artex for return instructions.

SYMPTOM

LIKELY CAUSE

ACTION

Meazura is “locked” up,

programs will not respond

Various

Perform “soft reset”

by holding down

both the power and backlight keys

simultaneously to perform a soft reset;

the Meazura stops what it was doing
and restarts.
All applications and data stored in the

handheld are retained.

Meazura will not respond to

“soft reset”

Various

Perform” hard reset” by doing a soft

reset but keeping the power key held

down until the Palm Powered



logo

appears.
A confirmation message is displayed

asking the user to confirm the hard

reset, whereby pressing the UP arrow

key will proceed with the process.
A hard reset does everything a soft

reset does, but also erases all

programs, data, patches, and user

information.

Meazura will not power on

Dead battery

Charge battery for at least 2 hours

Meazura will not reset

(either “soft” or “hard”)

Defective Meazura unit

Return unit to Artex

Meazura will not power on

with known good battery

Defective Meazura unit

Return unit to Artex

10.2

Technical Assistance

Programming ELTs with the proper information and the proper protocol is not always a

straightforward process.

Please be sure to thoroughly read this manual

. If

assistance is required, contact Artex in the United States at (954) 981-3333 or send e-

mail to

[email protected]

Содержание A3-06-2824-1












































Результаты поиска

Содержание A3-06-2824-1

Отзывы:

Похожие инструкции для A3-06-2824-1

Бренды по названию

Популярные бренды

ARTEX A3-06-2824-1, Руководство по эксплуатации

Результаты поиска

Содержание A3-06-2824-1

Отзывы:

Похожие инструкции для A3-06-2824-1

Бренды по названию

Популярные бренды