manualshive.com logo in svg

Artesyn MaxCore MC1600, Инструкция по установке и эксплуатации, Страница: 81 / 118

Поделиться
Скачать
Artesyn MaxCore MC1600 Скачать руководство пользователя страница 81

 

MC1600 Extreme Edge Server Installation and Use (6806870A02A)

79

 

Chapter 4

System Installation

4.1

Introduction

This chapter provides instructions for installing and removing the Extreme Edge Server in a rack 
or cabinet. It also provides information and procedures for grounding, powering up and down, 
and disconnecting the server from the power feed.

4.2

Before Installation

Refer to 

Front Panel Connectors, PCIe Slot, LEDs, and Ground Point on page 35

 for location of LEDs, 

connectors and earth ground point.

Before you start the installation, make sure that you have all of the necessary equipment and 
tools available.

Provide the following cables:

Earth grounding cable with an M4 ring lug in case of rack installation

Twisted pair Ethernet cable for connecting the BMC ETH

Twisted pair Ethernet cable for the front panel ETH1 and ETH2 RJ-45 ports

SFP+ or SFP modules or direct connect copper cables for the five SFP+ ports

The connectivity of the RJ-45 ports to CPU1 and/or CPU2 is covered in 

Figure 1-1

 and 

PCIe-Based 

Gigabit Ethernet

.

Usage

Equipment and Tools

General

Torque wrench
ESD wrist strap

Server / Rack / Cabinet

Four bolts or screws 6mm / 0.24" diameter

Grounding

Ground cable 1.25 mm

2 

for DC system

Power

DC power cable

System Access

USB Type-A to USB Type-A cable
PC or laptop

Содержание MaxCore MC1600























































































































Отзывы:

Нет отзывов