Artesyn MaxCore MC1600 Скачать руководство пользователя страница 91 | Manualshive

Страница: 91 / 118

Artesyn MaxCore MC1600 Скачать руководство пользователя страница 91

Software Configuration

MC1600 Extreme Edge Server Installation and Use (6806870A02A)

89

Show Operation:

Show Operation does not access any device. It only operates with the firmware image and it
shows the metadata, which is part of the image. Furthermore, it validates the firmware image
to compare the checksum part of the metadata against the checksum of the raw image. The
output of the Show Operation is similar to the output of the Query Operation. A sample output
of the BIOS image is shown below.

Show contents of BIOS firmware image:

Verification of BIOS image:

Upgrade Operation:

Upgrade Operation uploads the firmware image to the device. Before the upload process, the
firmware image is validated first and the FCU verifies if the image is applicable to the firmware
device.

To upgrade BIOS, use the following command:

$

fcu –uf <BIOS image>.fri

«
...
89
90
91
92
93
...
»

Содержание MaxCore MC1600























































































































Отзывы:

Нет отзывов