background image

Page 12 · 4200 Series 

LaserSource

 User’s Manual 

 

 

Shrt 

 

A short circuit has been detected on the output. 

OutT 

The unit is out-of-tolerance. See the 

Tol Time

 and 

Tol Io

 settings for 

more information. 

ILim 

The unit is in current limit. 

MLim 

The unit is in photodiode current limit. 

PLim 

The unit is in photodiode power limit. 

 

 

Settings and Menus 

 

 
All parameters of the 

LaserSource

 can be viewed and changed within the 

menu. The menus are constructed with the most used parameters first. To 
change any setting, press 

Menu

 to enter the menu then rotate the knob to select 

the parameter to change. Press the knob to begin changing the value. As a 
visual indication that you are in edit mode, you will see an asterisk appear next 
to the value. Once you have made your change, press the knob or 

Menu

 button 

to store the value. Pressing the 

Menu

 button will store and exit the menu, while 

pressing the knob will store the value but leave you in the menu to make 
additional changes. 
 
Some settings are contained inside a sub menu, such as communications 
settings. To access the sub menu, simply press the knob to enter the sub menu 

when its name is displayed. 
 
Below is a complete list of settings: 
 

Menu 

Description 

Factory 

Default 

Root Menu 

Top Level Menu 

 

Mode 

As described in the section above, Control 
Modes, the unit offers five control modes: Io 
(ACC), Io HiBW (ACC), Im (AMC), Po (APC), 
and Vf (AVC). Change this setting to select a 
new mode. 

Io (ACC) 

Io limit 

This setting controls the maximum amount of 

forward current that can be delivered to the 
laser diode. This limit is implemented in hard 
for immediate response. For more 
information about limits, see the section 
entitled “Hardware and Software Limits”. 

Maximum 

Содержание LaserSource 4205





























Отзывы: