background image

1 Film Magazine (200 ft.)  
2 Magazine Cover Lock  
3 Latch for Magazine Lock  
4 Camera Cover Lock  
5 Diopter Adjustment Ring  
6 Eyepiece Retaining Ring  
7 Lock for Diopter Adjustment  
8 Power Cable Lock  
9 Override Button for Buckle Switch  
10 Camera “ON” Switch  
11 Camera ”OFF” Switch  
12 Cover Lock Spring  
13  Magazine Opening Cover  
14  Tachometer  
15  Footage Counter  
16  Frame Counter  
17  Power Connector  
18  Viewfinder Cover Door  
19  Accessory Shoe  
20  Focusing Lever  
21  Contour Hand Grip  
22  Re-Set for Foota

g

e Counter  

23  Re-Set for Frame Counter  
24  Motor Lock Lever  
25  Variable Speed Motor  
26  Rheostat To Control Camera Speed  
27  Inching Knob  
28  Eyelet for Carrying Strap  
29  Knurled Dis, Camera Take-Up  
30  Locking Levers for Torque Motor  
31  Torque Motor  
32  Knurled Disc, Magazine Take-Up  
33  Film Supply Counter  
34  Forward/Reverse Switch for Torque Motor  
35  Knurled Disc, Magazine Supply  
36  Knurled Disc, Camera Supply  
37  Lens Turret  
38  Lens Retaining Lever  
39  Filter Stage, Rotating  
40  Filter Stage, Stationary  
41  Matte Slot  
42  Matte Box  
43  Matte Box Beam  
44  Lock Screw for Matte Box  
45  Lock Screw for Matte Box Stages  
46  Diaphragm Ring  
47  Turret-Rotating Grips  
48 Eyelet for Carrying Strap  

 

Содержание ARRIFLEX 16S























Отзывы: