Belgrado
Español
56
05060091 02 14/05/2010
N.B.Todas estas operaciones deben ser llevadas a cabo por personal técnico especializado.
8. Unión de los muebles (Fig. 9)
KIT UNIÓN CANAL
9. Conexión eléctrica (Fig. 10)
- El sistema eléctrico debe estar conectado a tierra.
- Controle ante todo que la tensión de alimentación corresponda a la indicada en los datos técnicos
(Fig. 2).
- El mueble debe estar protegido mediante un interruptor automático magnetotérmico omnipolar,
instalado antes del mismo en la línea, con características adecuadas y que actúe además como
interruptor general de aislamiento de la línea.
- Informe al operador sobre la posición del interruptor de manera que pueda acceder a él
oportunamente en caso de EMERGENCIA.
- Para garantizar un funcionamiento regular, es necesario que la variación de tensión máxima esté
entre +/- 6% del valor nominal.
- Revise que la línea de alimentación tenga cables de sección adecuada, esté protegida contra
sobrecorrientes y dispersiones a tierra, conforme a las normativas vigentes.
- El instalador debe suministrar los dispositivos de anclaje para todos los cables de entrada y salida del
mueble.
- En caso de interrupciones de la alimentación eléctrica, revise que todos los aparatos eléctricos de la tienda
puedan volverse a encender sin causar la intervención de los dispositivos de protección contra
sobrecargas; de no ser así, modifique la instalación para diferenciar la puesta en marcha de los diferentes
dispositivos.
- El interruptor automático magnetotérmico debe funcionar de tal manera que no se abra el circuito en
el neutro sin abrirlo a la vez en las fases; de cualquier manera la distancia de apertura de los
contactos debe ser de por lo menos 3 mm.
N.B.Todas estas operaciones deben ser llevadas a cabo por personal técnico especializado.
10.Control y regulación de la temperatura (Fig. 5-Fig. 6)
El control de la temperatura de refrigeración se realiza mediante el termómetro mecánico (Rif. 5) ubi-
cado en la chapa de aspiración o en el visualizador del termómetro/termostato CAREL (OPCIONAL)
que se encuentra en la parte inferior del mueble (Rif. 3).
Normalmente, el controlador se configura de fábrica en fase de prueba. En caso de cambio de la
programación, hacer referencia a las instrucciones de la empresa de fabricación del controlador.
ATENCIÓN!: Una regulación excesivamente baja de la temperatura podría comprometer el fun-
cionamiento regular del mueble alterando las normales pausas termostáticas.
N.B.Todas estas operaciones deben ser llevadas a cabo por personal técnico especializado.
11.Carga del mueble (Fig. 6)
Para reabastecer el mueble es necesario respetar algunas reglas importantes:
- disponga los productos de manera que no se supere por ningún motivo la línea de carga máxima
(Rif. 7); superar dicho límite significa obstaculizar la correcta circulación del aire, obteniendo
temperaturas de los productos más elevadas que pueden ocasionar la formación de hielo en el
evaporador;
- la disposición uniforme de los productos, sin zonas vacías, garantiza el mejor funcionamiento del
mueble;
- se recomienda agotar primero los productos que están en el mueble desde hace más tiempo
respecto a los nuevos (rotación de los alimentos).
Pos.
Denominación
Código
1
Clavija de alineación Ø 4x80
02940652
2
Tornillo TC 4x35
04715021
3
Arandela 5x10
04480107
4
Casquillo M4
04520006
5
Tornillo TC 4,2x19
04706021
6
Soporte cubrejuntas
01331077
7
Tuerca M8
04230600
8
Tornillo TCEI M8x120 cincado
04711065
9
Arandela 8,5x24 cincada
04480112
10
Cubrejuntas unión canal
01332222
11
Tornillo TCEI M8x80
04711030