Armstrong Flo-Direct Скачать руководство пользователя | Manualshive

Страница: 30 / 40

background image

30

Flo-Direct

®

Complete Thermal Exchange Gas Fired Water Heater

• Check the spark plug connection and wire.

• Check the Eclipse Veri-Flame controller (Fig 28-1):

This test procedure is designed to check for a false

fl ame signal after the start of the trial for ignition of the

burner. Close the ball valve on the top of the fuel train

near the top plate (Fig 29-1) The correct response of the

Eclipse Veri-Flame controller is:

A. If the burner is running, it will lose fl ame and then

the Eclipse Veri-Flame controller should have no

indication of fl ame and will de-energize the safety

shut-off valves.

B. If the burner is not running, create a demand to start

the burner and the Eclipse Veri-Flame controller

should not keep the safety shutoff valves open after the end of the trial for ignition. After that the

Eclipse Veri-Flame controller should have no indication of fl ame and it should de-energize the safety

shut-off valves.

If the Eclipse Veri-Flame controller does not respond as instructed above it failed the test and a hazard

condition exists.

Discontinue operation of the Flo-Direct CTE gas fi red water heater and consult Armstrong toll free

at 1-888-468-4673.

Annually

• Check that all electrical connections on the Flo-Direct CTE gas fi red water heater are secure.

• Check/Tighten all nuts/bolts.

• Visually inspect all accessible wetted parts for corrosion or mineral deposition.

• Check the integrity of the fuel train connections and fi ttings.

• Check the integrity of the water train connections and fi ttings

Figure 30-1.

«
...
28
29
30
31
32
...
»

Содержание Flo-Direct









































Отзывы:

Нет отзывов

Похожие инструкции для Flo-Direct

Бренд: Canature Страницы: 28

Бренд: Balcrank Страницы: 8

Бренд: Parker Страницы: 12

Бренд: Midea Страницы: 36

Бренд: Liberty Pumps Страницы: 16

Бренд: DAY Страницы: 51

Бренд: Flotec Страницы: 24

BLACKLIGHT 7815

Бренд: MO-EL Страницы: 12

Бренд: Parkside Страницы: 220

ESSENSSE NEO VCES3 AC Series

Бренд: 2VV Страницы: 20

Бренд: Nibe Страницы: 20

Бренд: OSNA Страницы: 40

FLORES C CH E - MOUNTING

Бренд: RADSON Страницы: 4

PTH38PSS, PTH38PCP, PTH38PGM

Бренд: Napoleon Страницы: 15

Бренд: Protemp Страницы: 30

Бренд: Bayrol Страницы: 56

MegaLife HE Series

Бренд: Heatrae Sadia Страницы: 24

Бренд: Gabarron Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды