ARM PL310 Скачать руководство пользователя страница 20

Страница: 20 / 60

Introduction

1-6

ARM DDI 0402B

Note

The interface of the MBIST controller communicates with both the ATE and the MBIST
interface of the cache controller. See Appendix A

Signal Descriptions

for descriptions

of the MBIST controller interface signals. See the

ARM PrimeCell Level 2 Cache

Controller (PL310) Technical Reference Manual

for more information about the

MBIST interface.

MBISTDCTL[19:0]

Input

Delayed versions of the

MBISTCE[17:0]

signal and the doubleword select signal,

MBISTADDR[1:0]

. Selects the correct read data after it passes through the MBIST

pipeline stages.

MBISTDCTL[19:0]

= delayed {

MBISTCE[17:0]

MBISTADDR[1:0]

MTESTON

Input

Select signal for cache RAM array. This signal is the select input to the multiplexors
that access the cache RAM arrays for test. When asserted,

MTESTON

takes priority

over all other select inputs to the multiplexors.

MBISTCE[17:0]

Input

One-hot chip enables to select cache RAM arrays for test.

MBISTWE[31:0]

Input

Global write enable signal for all RAM arrays.

MBISTADDR[19:0]

Input

Address signal for cache RAM array.

MBISTADDR[1:0]

is the doubleword select

value. See

Y-address and X-address fields, MBIR[36:33] and MBIR[40:37]

page 3-9 for a description of the doubleword select. Not all RAM arrays use the full
address width.

MBISTDIN[63:0]

Input

Data bus to the cache RAM arrays. Not all RAM arrays use the full data width.

Table 1-1 Cache controller MBIST interface signals (continued)

Name

Type

Description

Содержание PL310
























































Результаты поиска

Содержание PL310

Отзывы:

ARM PL310, Техническое справочное руководство, Страница: 20 / 60

Результаты поиска

Содержание PL310

Отзывы: