ARM Cortex-M4 Скачать руководство пользователя страница 245 | Manualshive

Страница: 245 / 276

ARM Cortex-M4 Скачать руководство пользователя страница 245

Cortex-M4 Peripherals

ARM DUI 0553A

Copyright © 2010 ARM. All rights reserved.

4-29

ID121610

Non-Confidential

Note

The UFSR bits are sticky. This means as one or more fault occurs, the associated bits are set to
1. A bit that is set to 1 is cleared to 0 only by writing 1 to that bit, or by a reset.

[2]

INVPC

Invalid PC load UsageFault, caused by an invalid PC load by EXC_RETURN:
0 = no invalid PC load UsageFault
1 = the processor has attempted an illegal load of EXC_RETURN to the PC, as a result of an invalid
context, or an invalid EXC_RETURN value.
When this bit is set to 1, the PC value stacked for the exception return points to the instruction that tried
to perform the illegal load of the PC.

[1]

INVSTATE

Invalid state UsageFault:
0 = no invalid state UsageFault
1 = the processor has attempted to execute an instruction that makes illegal use of the EPSR.
When this bit is set to 1, the PC value stacked for the exception return points to the instruction that
attempted the illegal use of the EPSR.
This bit is not set to 1 if an undefined instruction uses the EPSR.

[0]

UNDEFINSTR

Undefined instruction UsageFault:
0 = no undefined instruction UsageFault
1 = the processor has attempted to execute an undefined instruction.
When this bit is set to 1, the PC value stacked for the exception return points to the undefined instruction.
An undefined instruction is an instruction that the processor cannot decode.

Table 4-27 UFSR bit assignments (continued)

Bits

Name

Function

«
...
243
244
245
246
247
...
»

Содержание Cortex-M4





















































































































































































































































































Отзывы:

Нет отзывов