ARM Cortex-M4 страница 20 Скачать руководство пользователя

Страница: 20 / 276

The Cortex-M4 Processor

ARM DUI 0553A

2-7

ID121610

Non-Confidential

Attempts to read the EPSR directly through application software using the

MSR

instruction

always return zero. Attempts to write the EPSR using the

MSR

instruction in application software

are ignored.

Interruptible-continuable instructions

When an interrupt occurs during the execution of an

LDM

STM

PUSH

, or

POP

instruction, and when

an FPU is implemented an

VLDM

VSTM

VPUSH

, or

VPOP

instruction, the processor:

•

stops the load multiple or store multiple instruction operation temporarily

•

stores the next register operand in the multiple operation to EPSR bits[15:12].

After servicing the interrupt, the processor:
•

returns to the register pointed to by bits[15:12]

•

resumes execution of the multiple load or store instruction.

When the EPSR holds ICI execution state, bits[26:25,11:10] are zero.

If-Then block

The If-Then block contains up to four instructions following an

instruction. Each instruction

in the block is conditional. The conditions for the instructions are either all the same, or some
can be the inverse of others. See

on page 3-122

for more information.

Thumb state

The Cortex-M4 processor only supports execution of instructions in Thumb state. The following
can clear the T bit to 0:
•

instructions

BLX

and

POP{PC

}

•

restoration from the stacked xPSR value on an exception return

•

bit[0] of the vector value on an exception entry or reset.

Attempting to execute instructions when the T bit is 0 results in a fault or lockup. See

Lockup

on page 2-31

for more information.

Exception mask registers

The exception mask registers disable the handling of exceptions by the processor. Disable
exceptions where they might impact on timing critical tasks.

To access the exception mask registers use the

MSR

and

MRS

instructions, or the

CPS

instruction to

change the value of PRIMASK or FAULTMASK. See

for more information.

[24]

Thumb state bit, see

Thumb state

[23:16]

Reserved.

[9:0]

Reserved.

Table 2-6 EPSR bit assignments (continued)

Bits

Name

Function

Содержание Cortex-M4



















































































































































































































































































Результаты поиска

Содержание Cortex-M4

Отзывы:

Похожие инструкции для Cortex-M4

Бренды по названию

Популярные бренды

ARM Cortex-M4, Универсальное руководство пользователя

Результаты поиска

Содержание Cortex-M4

Отзывы:

Похожие инструкции для Cortex-M4

Бренды по названию

Популярные бренды