manualshive.com logo in svg

ARM Cortex-M4, Универсальное руководство пользователя, Страница: 12 / 276

Поделиться
Скачать
ARM Cortex-M4 Скачать руководство пользователя страница 12

Introduction 

ARM DUI 0553A

Copyright © 2010 ARM. All rights reserved.

1-3

ID121610

Non-Confidential

Routines

 (ISRs), dramatically reducing the interrupt latency. This is achieved through the 

hardware stacking of registers, and the ability to suspend load-multiple and store-multiple 
operations. Interrupt handlers do not require wrapping in assembler code, removing any code 
overhead from the ISRs. A tail-chain optimization also significantly reduces the overhead when 
switching from one ISR to another.

To optimize low-power designs, the NVIC integrates with the sleep modes, that includes an 
optional deep sleep function. This enables the entire device to be rapidly powered down while 
still retaining program state.

1.1.1

System-level interface

The Cortex-M4 processor provides multiple interfaces using AMBA

®

 technology to provide 

high speed, low latency memory accesses. It supports unaligned data accesses and implements 
atomic bit manipulation that enables faster peripheral controls, system spinlocks and thread-safe 
Boolean data handling.

The Cortex-M4 processor has an optional 

Memory Protection Unit

 (MPU) that permits control 

of individual regions in memory, enabling applications to utilize multiple privilege levels, 
separating and protecting code, data and stack on a task-by-task basis. Such requirements are 
becoming critical in many embedded applications such as automotive.

1.1.2

Optional integrated configurable debug

The Cortex-M4 processor can implement a complete hardware debug solution. This provides 
high system visibility of the processor and memory through either a traditional JTAG port or a 
2-pin 

Serial Wire Debug

 (SWD) port that is ideal for microcontrollers and other small package 

devices.

For system trace the processor integrates an 

Instrumentation Trace Macrocell

 (ITM) alongside 

data watchpoints and a profiling unit. To enable simple and cost-effective profiling of the system 
events these generate, a 

Serial Wire Viewer

 (SWV) can export a stream of software-generated 

messages, data trace, and profiling information through a single pin.

The optional 

Embedded Trace Macrocell

™

 (ETM) delivers unrivalled instruction trace capture 

in an area far smaller than traditional trace units, enabling many low cost MCUs to implement 
full instruction trace for the first time.

The optional 

Flash Patch and Breakpoint Unit

 (FPB) provides up to eight hardware breakpoint 

comparators that debuggers can use. The comparators in the FPB also provide remap functions 
of up to eight words in the program code in the CODE memory region. This enables applications 
stored on a non-erasable, ROM-based microcontroller to be patched if a small programmable 
memory, for example flash, is available in the device. During initialization, the application in 
ROM detects, from the programmable memory, whether a patch is required. If a patch is 
required, the application programs the FPB to remap a number of addresses. When those 
addresses are accessed, the accesses are redirected to a remap table specified in the FPB 
configuration, which means the program in the non-modifiable ROM can be patched.

1.1.3

Cortex-M4 processor features and benefits summary

•

tight integration of system peripherals reduces area and development costs

•

Thumb instruction set combines high code density with 32-bit performance

•

optional IEEE754-compliant single-precision FPU

•

code-patch ability for ROM system updates

•

power control optimization of system components

•

integrated sleep modes for low power consumption

Содержание Cortex-M4





















































































































































































































































































Отзывы:

Нет отзывов