ARM Cortex-M4 страница 267 Скачать руководство пользователя

Страница: 267 / 276

Cortex-M4 Peripherals

ARM DUI 0553A

4-51

ID121610

Non-Confidential

[26]

AHP

Alternative half-precision control bit:

IEEE half-precision format selected.

Alternative half-precision format selected.

[25]

Default NaN mode control bit:

NaN operands propagate through to the output of a floating-point operation.

Any operation involving one or more NaNs returns the Default NaN.

[24]

Flush-to-zero mode control bit:

Flush-to-zero mode disabled. Behavior of the floating-point system is fully
compliant with the IEEE 754 standard.

Flush-to-zero mode enabled.

[23:22]

RMode

Rounding Mode control field. The encoding of this field is:

0b00

Round to Nearest

(RN) mode

0b01

Round towards Plus Infinity

(RP) mode

0b10

Round towards Minus Infinity

(RM) mode

0b11

Round towards Zero

(RZ) mode.

The specified rounding mode is used by almost all floating-point instructions.

[21:8]

Reserved.

[7]

IDC

Input Denormal cumulative exception bit, see bits [4:0].

[6:5]

Reserved.

[4]

IXC

Cumulative exception bits for floating-point exceptions, see also bit [7]. Each of these bits is
set to 1 to indicate that the corresponding exception has occurred since 0 was last written to it.

IDC, bit[7]

Input Denormal cumulative exception bit.

IXC

Inexact cumulative exception bit.

UFC

Underflow cumulative exception bit.

OFC

Overflow cumulative exception bit.

DZC

Division by Zero cumulative exception bit.

IOC

Invalid Operation cumulative exception bit.

[3]

UFC

[2]

OFC

[1]

DZC

[0]

IOC

Table 4-53 FPSCR bit assignments (continued)

Bits

Name

Function

Содержание Cortex-M4



















































































































































































































































































Результаты поиска

Содержание Cortex-M4

Отзывы:

Похожие инструкции для Cortex-M4

Бренды по названию

Популярные бренды

ARM Cortex-M4, Универсальное руководство пользователя

Результаты поиска

Содержание Cortex-M4

Отзывы:

Похожие инструкции для Cortex-M4

Бренды по названию

Популярные бренды