manualshive.com logo in svg

Arlyn Scales ArlynGuard S MKE-5-IS-SP, Инструкция по эксплуатации

Поделиться
Скачать
Arlyn Scales ArlynGuard S MKE-5-IS-SP Скачать руководство пользователя страница 27

 

27 

INTRODUCTION TO OPTIONS 

This section will cover the operation and setup of all of the options available for your scale. It is important to note that some described 
menu items will be missing if that option was not installed in your specific scale. All of the options listed may be installed in any scale 

and may run concurrently. Any of the options may be installed later at the factory if it wasn’t installed at time of purchase

. Call our 

service department for details. 

RS422 COMMUNICATION 

The RS422 option is a fully capable, bi-directional communications port. The port can be configured to operate at a variety of baud 
rates and the output data frames are definable by the user. The printing of a frame can be initiated by pressing the print button, by an 
external command or continuously when the print stream mode is activated. 

The communications port also contains an extensive external command interface allowing the ability to perform remote key presses. 

RS422

A
B
Z
Y

GND

 

Configuring the Port 

Baud rate and other parameters can be configured through the Port Configuration screen that can be accessed under menu SETUP 
MENU/OPTION SETUPS/RS485/PORT CONFIG. The options are shown below. The UI 

of “RS485” is used for communication via RS422. 

 

BAUD RATE 

Settable to 110, 150, 300, 600, 1200, 2400, 4800, 9600, 19200, 31250 or 38400 bits per second. 

DATA BITS 

Seven or Eight 

STOP BITS 

One or Two 

PARITY   

Even, odd or none 

ECHO 

On or off. When echo is enabled the scale will echo each character the scale receives back to the user. 

 

<RS422 indicator depiction> 

Perform Test Print 

As an aid to port configuration we have included a “perform test print” function to the RS

485 menu. Executing this will cause your 

current Print Frame to print. To access this function, go to the menu SETUP MENU/OPTION SETUPS/RS485/PERFORM TEST PRINT. 

Loop Back Test 

You may also test the operation of the RS422 port by performing a loop back test. On the output connector, A->Z and B->Y 
(transmitted and received data) need to be shorted together. When you perform the test, the scale sends data and reads it back 
through its own port, where it is compared and the results are show.  

Содержание ArlynGuard S MKE-5-IS-SP






















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды