manualshive.com logo in svg

Arizona Instrument JEROME 431-X, Руководство по эксплуатации

Поделиться
Скачать
Arizona Instrument JEROME 431-X Скачать руководство пользователя страница 23

AZI Customer Service 800-528-7411 or 602-470-1414 

Page 23 of 56

 

•

 

Replace the discarded fuse with the spare fuse located in the slide-out spare fuse 
compartment. 

•

 

Replace the fuse compartment in the power receptacle. 

 

As soon as possible, replace the spare fuse with another 1A, 250V, time delay fuse, AZI 
P/N 5100 1012). 

 
 

6.

 

CALIBRATION 

 
The Jerome

®

 431-X's gold film sensor is inherently stable and does not require frequent 

calibration.  The interval between calibrations depends upon the application and frequency of 
use; however, the recommended interval is every 12 months. 
 
The Jerome

®

 431-X has been factory calibrated using laboratory equipment containing NIST 

traceable permeation tubes.  In order to calibrate the Jerome

®

 431-X, a sophisticated calibration 

system is required that ensures stability of the calibration gas source, eliminates any pressure in 
the calibration gas stream, and controls the temperature of the calibration environment. 
 
We strongly recommend you take advantage of our calibration and maintenance service at 
Arizona Instrument.  Call Customer Service at (800) 528-7411 or (602) 470-1414 to arrange re-
calibration.  A certificate of calibration is issued from AZI when your instrument is factory 
calibrated. 

 
 

Verification of Functionality and Quality Control 

 
The Functional Test Kit (FTK), AZI P/N Y431 0902, is used to determine if your instrument is 
functioning correctly between recommended annual factory calibrations.  It allows you to have 
complete confidence in the sample results.  This test verifies proper instrument operation through 
the introduction of a known concentration of Mercury Vapor into the Jerome

®

 analyzer. 

  

 

THIS IS A FIELD CHECK OF THE FUNCTIONALITY OF THE INSTRUMENT. 

 

THIS TEST DOES NOT CALIBRATE THE INSTRUMENT.

 

 
If your application requires frequent verification of instrument function, this test demonstrates 
the unit’s operation and function.  Recording FTK results in an instrument log provides a quality 
control/quality assurance record of instrument function between regular calibrations.  If test 
results fall within the expected range, you may assume the instrument is functioning correctly. 

 

See APPENDIX A - 431-X FUNCTIONAL TEST KIT on page 37 for more information about 
the FTK procedures.  Complete instructions for use are supplied with the test kit, AZI P/N Y431 
0902. 

 
To order the FTK, contact your AZI Sales Representative at (800) 528-7411 or (602) 470-1414. 

 

Содержание JEROME 431-X

























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды