manualshive.com logo in svg

Aritech 1X-X3, Руководство по эксплуатации, Страница: 30 / 38

Поделиться
Скачать
Aritech 1X-X3 Скачать руководство пользователя страница 30

 

24 

1X-X3 Operation Manual 

Testing fire routing 
Note: 

Before performing any fire routing tests, ensure that the fire routing signals 

are not connected or notify the fire brigade of the tests. 
To test fire routing, press the General Test button, and then press the Fire 

Routing Start button. 
The test is indicated as follows: 
•  A steady General Test LED 
•  A steady yellow Fire Routing On LED 
•  A flashing Fire Routing On LED and the test signal (3 seconds on, 5 seconds 

off) without any configured delay for the duration of the test 

To end the test, press the General Test button, and then press the Fire Routing 

On button again. 
If there is an extinguishing preactivation, activation, release, or fire alarm event 

during the test, the control panel exits the test and responds to the alarm event 

as configured. 

Disabling or enabling a zone 

To disable a zone, press the General Disable button, and then press the 

corresponding Zone button. 
The disablement is indicated as follows: 
•  A steady General Disable LED 
•  A steady yellow Zone LED 
To enable the zone, press the General Disable button, and then press the Zone 

button again. 

Note: 

No fire alarm or faults are indicated for disabled zones. 

Содержание 1X-X3







































Отзывы:

Нет отзывов