Aritech 1X-X3 Скачать руководство пользователя страница 29 | Manualshive

Страница: 29 / 38

Aritech 1X-X3 Скачать руководство пользователя страница 29

1X-X3 Operation Manual

23

Disabling or enabling a fire sounders delay

To disable a configured (and enabled) fire sounders delay, press the Fire

Sounders Delay button. To enable the delay, press the button again.
If an alarm is reported in a zone linked to the extinguishing event, any configured

delay will be ignored and fire sounders will be activated immediately.

Testing sounders

To test the sounders, press the General Test button, and then press the Fire

Sounders Delay button.
Sounders can only be tested when the control panel is in standby state.
The test is indicated as follows:
•  A steady General Test LED
•  A steady yellow LED for the Fire Sounders Delay button
•  The audible sounder test signal (3 seconds on, 5 seconds off) for the duration

of the test, without any configured delay

To end the test, press the General Test button, and then press the corresponding

sounder Fire Sounders Delay button again.
If there is an extinguishing preactivation, activation, release, or fire alarm event

during the test, the control panel exits the test and responds to the alarm event

as configured.

Disabling or enabling fire routing

To disable fire routing, press the General Disable button, and then press the Fire

Routing Start button.
The disablement is indicated as follows:
• A steady General Disable LED

• A steady yellow Fire Routing On LED
To enable fire routing, press the General Disable button, and then press the Fire

Routing On button again.

Note:

Disabled fire routing does not operate or indicate a fault if there is a fire

alarm.

Disabling or enabling a fire routing delay

To disable a configured (and enabled) fire routing delay, press the Fire Routing

Delay button. To enable the delay, press the button again.

«
...
27
28
29
30
31
...
»

Содержание 1X-X3







































Отзывы:

Нет отзывов