Ariens 961469, Руководство пользователя

Страница: 12 / 24

12
LA
WN MOWER
Always observe safety rules when per- form
ing any main
te
nance.
TIRES •
Keep tires free of gasoline, oil, or insect control chemi
cals which can harm rub-
ber
.
•
A
void stumps, stones, deep ruts, sharp
objects and other hazards that may cause tire damage.
DRIVE WHEELS Check front drive wheels each time be
fore
you mow to be sure they move freely
.
The wheels not turning freely means trash, grass cuttings, etc. are in the drive wheel area and must be cleaned to free drive wheels. If necessary to clean the drive wheels, be sure to clean both front wheels. 1.
Remove hubcaps, locknuts & washers.
2.
Remove wheels from wheel ad
just
ers.
3.
Remove any trash or grass cuttings from inside the dust cover
, pinion and/
or drive wheel gear teeth.
4.
Put wheels back in place.
NOTE:
If after cleaning, the drive wheels
do not turn freely
, contact a qualifi
ed
service center
.
BLADE CARE
For best results, mower blade must be kept sharp. Re
place a bent or dam
aged
blade.
CAUTION:
Use only a replacement
blade approved by the manufacturer of your mower
. Using a blade not approved
by the manufacturer of your mower is haz- ardous, could damage your mower and void your warranty
.
T
O
REMOVE BLADE
1.
Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug.
2.
T
urn lawn mower on its side. Make
sure air fi
lter and carburetor are up.
3.
Use a wood block between blade and mower hous
ing to prevent blade from
turning when re
mov
ing blade bolt.
NOTE:
Protect your hands with gloves
and/or wrap blade with heavy cloth. 4.
Remove blade bolt by turning counter- clockwise.
5.
Remove blade and attaching hard- ware (bolt, lock wash
er and hardened
wash
er).
NOTE
: Remove the blade adapter and
check the key inside hub of blade adapter
.
The key must be in good condition to work properly
. Replace adapter if damaged.
T
O
REPLACE BLADE
1.
Position the blade adapter on the en- gine crank
shaft. Be sure key in adapter
and crankshaft keyway are aligned.
2.
Position blade on the blade adapter
.
IMPOR
T
ANT
:
T
o
ensure proper as
sem
bly
,
center hole in blade must align with star on blade adapter
.
3.
Be sure the trailing edge of blade (op- posite sharp edge) is up toward the engine.
4.
Install the blade bolt with the lock washer and hardened washer into blade adapter and crankshaft.
5.
Use block of wood between blade and lawn mower housing and tighten the blade bolt, turning clockwise.
•
The recommended tightening torque is 35–40 ft. lbs.
IMPOR
T
ANT
: Blade bolt is heat treated.
If bolt needs replacing, replace only with approved bolt shown in the Repair Parts section of this manual. T
O
SHARPEN BLADE
NOTE
: W
e
do not recommend sharp
en-
ing blade - but if you do, be sure the blade is balanced.
An un
bal
anced blade will
cause eventual damage to lawn mower or engine. •
The blade can be sharp
ened with a fi
le
or on a grinding wheel. Do not attempt to sharpen while on the mower
.
•
T
o
check blade balance, you will need a
5/8" diameter steel bolt, pin, or a cone balancer
. (When using a cone bal
anc
er
,
follow the in
struc
tions supplied with
bal
anc
er
.)
NOTE:
Do not use a nail for balancing
blade.
The lobes of the center hole may
appear to be centered, but are not.
Blade bolt
Crankshaft
keyway
Hardened washer
Lockwasher Blade adapter
Key
Blade
T
railing edge
Crankshaft
Belt
retainer
37
V
ibración
1.
Cuchilla desgastada, doblada
1.
Cambie la cuchilla.
Apriete el
excesiva
o suelta.
perno de la cuchilla.
2.
Cigueñal del motor doblado.
2.
Póngase en contacto con su centro
de
servicio
cualifi
cado.
Cordón
1.
El freno del volante del motor
1.
Presione la barra de control
arrancador
está aplicado cuando se
hacia el mango superior antes
difícil de tirar
suelta la barra de control.
de tirar el cordón arrancador
.
2.
Cigueñal del motor doblado.
2.
Póngase en contacto con su centro
de
servicio
cualifi
cado.
3.
Adaptador de la cuchilla quebrado.
3.
Cambie el adaptador de la cuchilla.
4.
La cuchilla se arrastra en
4.
Mueva la segadora a un lugar
el césped.
en donde el césped ha sido cortado o a una superfi
cie fi
rme
para hacer arrancar el motor
.
Recogedor de
1.
Altura de corte demasiado baja.
1.
Eleve la altura de corte.
césped no se
2.
Levantamiento de la cuchilla
2.
Cambie las cuchillas.
llena (si viene
desgastado.
equipado)
3.
Recogedor sin ventilación de aire.
3.
Limpie el recogedor de césped.
Difícil de
1.
El césped está demasiado alto o la
1.
Eleve la altura de corte.
empujar
altura de la rueda demasiado baja.
2.
Parte trasera de la
2.
Eleve la parte trasera de la caja de
caja/cuchilla de la segadora
la segadora (1) un lugar más alto.
arrastrándose en el césped.
3.
Recogedor de césped
3.
V
acíe el recogedor de césped.
demasiado
lleno.
4.
Posición de la altura del mango
4.
Ajuste la altura del mango de
no adecuada para usted.
modo que le acomode.
Pérdida de
1.
Desgaste de la correa.
1.
Re
vise/cambie correa de impulsión.
impulsión
2.
La correa está fuera de la polea.
2.
Revise/vuelva a instalar la
o retardase
3.
Cable de la impulsión usado o roto.
3.
Cambie el cable de la impulsión.
de la
4.
El sistema de control del
4.
Ajuste el control del mecanismo
velocidad
mecanismo impulsor “suelto”.
impulsor
.
PROBLEMA
CAUSA
CORRECCIÓN
SOLUCIÓN DE PROBLEMAS - V
ea la sección apropiada en el manual amenos que
esté dirigido a un centro de servico cualifi
cado.