manualshive.com logo in svg

ARI ARI-PACO 2G, Инструкции по эксплуатации и монтажу

Поделиться
Скачать
ARI ARI-PACO 2G Скачать руководство пользователя страница 14

Page 2-14

0040501006 2422

- Translated original instructions -

Operating and installation instructions

Thrust actuator ARI-PREMIO

®

-Plus 2G

4.5.3  Design notes

4.5.3.1  Control signal

- At the 4 - 20 mA signal, from a control signal < 3.6 mA, control signal failure will be detected.
- A cable break is detected in both the current signal 4 - 20 mA as well as the voltage signal 2 - 10 V.
- The control signal range is fixed from 0 - 10 V, resp. 4 - 20 mA. From software version 3.x.x 

upwards it is possible to set alternatively the voltage signal for auf 2 - 10 V via the diagnostics 

interface and PC. The 2 - 10 V then apply also for the feedback signal. A diagnostics connector 

and instructions  can be ordered on request.

- The 3 point control signal has a higher priority than the analogue control signal. This can for 

example be used for frost protection or a local control.
In a concurrent control in direction OPEN and CLOSED, over the 3-point control signal, the motor 
stops, so that the drive no longer follows the analogue input signal.

- The switch positions for control signal type and inversion affects to the analogue input and 

feedback signal. There are no separate settings for the input and feedback signal possible.

4.5.3.2  Behavior in control signal failure / error

- 

The fail-safe behaviour in case of a control signal failure or a cable break can be set for the 

analogue control signal with a 3-step slide switch: OPEN – STOP – CLOSED

.

- 

Alternatively, any position between 0 - 100 % can be submitted via the diagnostics interface and 

PC. At 101 %, the actuator rests at his most recent position.

In order to specify the fail-safe position using the switches again, you must enter in the software a 
value of 102 % for this position.

ATTENTION !

 

In the same way as in the older software versions (at values between 0-101%), the 
slide switch sets three different actuator characteristics that define the relationship 
between the input signal and the valve position. For a linear relationship please set this 
switch to the lowest position.

Содержание ARI-PACO 2G





















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды