Arctic Cat 2015 M 6000 Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 64

background image

5

RR

0746-789

Gasoline-Oil

Recommended Gasoline

The recommended gasoline to use in this

snowmobile is minimum 91 octane gaso-

line with a maximum 10% ethanol content.



NOTE: For optimum performance,

use only 91 octane (minimum) gasoline.

Gasolines containing more than 10% eth-

anol are not acceptable gasoline for use

in this snowmobile. Do not use gasolines

containing methanol.

Recommended Injection

Oil

The recommended oil to use in the oil-

injection system is Arctic Cat C-TEC2

Synthetic 2-Cycle Oil (p/n 6639-520 - 48

oz) This oil is specially formulated to be

used and meets all of the lubrication

requirements of the Arctic Cat C-TEC2

snowmobile engine.

Filling Gas Tank

Since gasoline expands as its temperature

increases, the gas tank must be filled to

its rated capacity only. Expansion room

must be maintained in the tank particu-

larly if the tank is filled with cold gaso-

line and then moved to a warm area.
Also, if the snowmobile is to remain on a

trailer after filling the gas tank, the bed of

the trailer must be maintained level to

prevent gasoline from draining out

through the gas tank vent hose.

Break-In Gas/Oil Mixing

Instructions (8000)

Before mixing gasoline and oil, make sure

the oil is at room temperature (20° C/68°

F). Use a U.L. approved 22.7 L (6 U.S.

gal.) gasoline container for mixing the gas-

oline and oil. To properly mix the fuel at a

100:1 ratio, use the following procedure:

CAUTION

Do not use white gas or gasolines
containing methanol. Only Arctic Cat
approved gasoline additives should
be used.

CAUTION

If a situation arises wherein 91 octane
non ethanol or 91 octane with maximum
10% ethanol gasoline is not available, 87
octane gasoline can be substituted in
an emergency; however, the prolonged
usage of 87 octane gasoline can cause
severe engine damage.

CAUTION

Any oil used in place of the recom-
mended oil could cause serious
engine damage.

! WARNING

Always fill the gas tank in a well-venti-
lated area. Never add gasoline to the
snowmobile gas tank near any open
flames or with the engine running. DO
NOT SMOKE while filling the gas tank.
Do not sit on the snowmobile without
first installing the gas tank cap.

CAUTION

Never mix oil and gasoline in the
snowmobile gas tank.

«
...
7
8
9
10
11
...
»

Содержание 2015 M 6000

































































Отзывы:

Нет отзывов

Похожие инструкции для 2015 M 6000

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды