Arctic Cat 2015 M 6000 Скачать руководство пользователя страница 50

Страница: 50 / 64

4. Install the rubber grommet; then

connect the headlight harness con-

nector to the bulb.

5. Check headlight aim.

Adjusting Headlight Aim

The headlight can be adjusted for vertical

aim of the HIGH/LOW beam. The geo-

metric center of HIGH beam zone is to be

used for vertical aiming.

1. Position the snowmobile on a level

floor so the headlight is approxi-

mately 8 m (25 ft) from an aiming

surface (wall or similar surface).



NOTE: There should be an “aver-

age” operating load on the snowmo-
bile when adjusting headlight aim.

2. Measure the distance from the floor

to midpoint of the headlight.

3. Using the measurement obtained in

step 2, make a horizontal mark on

the aiming surface.

4. Make a vertical mark which inter-

sects the horizontal mark on the aim-

ing surface directly in front of the

headlight.

5. Engage the brake lever lock and start

the engine. Move the headlight dim-

mer switch to the HIGH beam posi-

tion. DO NOT USE LOW BEAM.

6. Observe the headlight beam aim.

Proper aim is when the most intense

beam is centered on the vertical mark

5 cm (2 in.) below the horizontal

mark on the aiming surface.

0745-813

7. Adjust the headlight using the

adjusting screw on the backside of

the headlight using a 4 mm swivel

socket and long extension until cor-

rect aim is obtained. Shut the engine

off; then disengage the brake lever

lock.

0746-807

Ski Wear Bars

The ski wear bar is a replaceable bar

attached to the underside of the ski. The

purpose of the wear bar is to assist in

turning the snowmobile, to minimize ski

wear, and to maintain good steering con-

trol. If the snowmobile is operated pri-

marily in deep snow, ski wear bar wear

will be minimal; however, if the snow-

mobile is operated on terrain where the

snow cover is minimal, the ski wear bar

will wear faster. To maintain positive

steering characteristics, Arctic Cat rec-

ommends that the ski wear bars be

checked before each use and replaced if

worn beyond 1/2 of the original diameter.

Ski wear bars are available from an

authorized Arctic Cat Snowmobile

dealer.

! WARNING

Do not operate the snowmobile
unless headlight beam is adjusted
properly. An incorrectly adjusted
beam will not provide the operator
the optimum amount of light.

! WARNING

Operating the snowmobile with
excessively worn ski wear bars may
result in a loss of steering control.

Содержание 2015 M 6000

































































Результаты поиска

Содержание 2015 M 6000

Отзывы:

Похожие инструкции для 2015 M 6000

Бренды по названию

Популярные бренды

Arctic Cat 2015 M 6000, Руководство оператора

Результаты поиска

Содержание 2015 M 6000

Отзывы:

Похожие инструкции для 2015 M 6000

Бренды по названию

Популярные бренды