Arctic Cat 2015 M 6000 Скачать руководство пользователя страница 49

Страница: 49 / 64

To rotate an adjusting cam, use the spark

plug wrench from the tool kit. Rotate the

wrench until the cam is in the desired

position. To stiffen the ride, rotate the cam

so as to raise the spring end. Make the

appropriate adjustment on the other cam.

Adjusting Skid Frame Rear

Arm Shock Spring (M/XF)

Proper adjustment of rear arm shock

absorber spring pre-load is necessary to

get the most desirable ride.
The rear arm shock spring is adjustable

for the terrain conditions and driving

style and weight of the operator. The

spring adjuster nut has been set at the fac-

tory so the correct amount of threads are

exposed between the adjuster nut and the

threaded shock body as an initial setting.
Rear spring pre-load adjustment is

accomplished by loosening the adjuster

nut locking collar (B) from the adjuster

nut (A) and using the Spring Adjuster

Tool from the tool kit, rotating the

adjuster nut in whichever direction is

desired. Tighten the locking collar

against the adjuster nut.

0745-159

Lights

For the correct headlight bulb and/or tail-

light/brakelight LED, see the appropriate

specifications sheet.

Removing and Installing

Taillight/Brakelight

These models are equipped with an LED

taillight/brakelight. If the LED fails, it

must be replaced. To remove and install

the LED, use the following procedure.

746-097B

1. Disconnect the taillight harness con-

nector.

2. Remove the two torx-head screws

securing the taillight to the bracket.

3. Connect the taillight harness connec-

tor; then secure the taillight to the

bracket with the two torx-head

screws.

Removing/Installing

Headlight Bulb



NOTE: The bulb portion of headlight

is fragile. HANDLE WITH CARE. When
replacing the headlight bulb, the bulb
assembly must first be removed from
the housing. Do not touch the glass
portion of the bulb. If the glass is
touched, it must be cleaned with a dry
cloth before installing.

1. Disconnect the headlight harness

connector from the bulb; then

remove the rubber grommet from

the headlight housing.

2. Rotate the bulb retainer counter-

clockwise until it unlocks from the

housing; then remove the bulb.

0746-096

3. Install the bulb and retainer; then

rotate the retainer clockwise until it

properly locks in place.

Содержание 2015 M 6000

































































Результаты поиска

Содержание 2015 M 6000

Отзывы:

Похожие инструкции для 2015 M 6000

Бренды по названию

Популярные бренды

Arctic Cat 2015 M 6000, Руководство оператора

Результаты поиска

Содержание 2015 M 6000

Отзывы:

Похожие инструкции для 2015 M 6000

Бренды по названию

Популярные бренды