Arctic Cat 2015 M 6000 Скачать руководство пользователя

Страница: 41 / 64

1. Remove the brake fluid reservoir cover;

then remove most of the brake fluid

from the reservoir. Install the cover.



NOTE: The above procedure will

allow room for the fluid from the cali-
per when the pistons are pushed
into the caliper for installing new
brake pads. Replacing the cover will
prevent fluid spillage.

2. Open the left-side access panel.
3. Remove the torx-head screws secur-

ing the brake shield to the belt guard

mount; then remove the cap screws

securing the brake shield to the

brake caliper.

4. Carefully move the shield out of the

way; then remove the hairpin clip

securing the brake pads to the cali-

per assembly.

5. Using a pair of pliers, pull the outer

brake pad out of the caliper assembly.

PC013



NOTE: Changing one pad at a time

will prevent one piston from pushing
out the other piston from the caliper.

6. Measure the thickness of the brake

pad. The brake pad thickness must

be greater than 5.0 mm (0.20 in.). If

the brake pad thickness is less than

specified, replacement of both pads

is necessary.

PC011A

7. Using a flat-blade tool, slowly and

carefully push the piston into the

caliper.

8. Position the outer brake pad into the

caliper; then install the hair-pin clip

into the caliper assembly.

9. Repeat steps 5-8 for the inner pad;

then secure the pad with the hairpin

clip.

10. Remove the reservoir cover and

remove the remaining fluid; then fill

the reservoir with fresh fluid and

install the cover.

11. Pump the brake lever to ensure cor-

rect positioning of the brake pads and

proper brake lever travel; then release.



NOTE: If brake lever travel is not

within specification, bleed the brake
system.

12. Remove the reservoir cover and fill

the reservoir (if necessary) to the

proper level with fresh brake fluid;

then install the cover.

13. Secure the brake shield, the driven

clutch (tightened to 20 ft-lb); then

close and secure the left-side access

panel.



NOTE: When new brake pads are

installed, a “burnishing” process is
required (see Burnishing Brake Pads
sub-section).

Burnishing Brake Pads

After changing brake pads, the new brake

pads must be burnished to achieve full

braking effectiveness. Braking distance

will be extended until brake pads are

properly burnished.
To properly burnish the brakes, use fol-

lowing procedure:

CAUTION

Brake fluid is highly corrosive. Do not
spill brake fluid on any surface of the
snowmobile.

Содержание 2015 M 6000

































































Результаты поиска

Содержание 2015 M 6000

Отзывы:

Похожие инструкции для 2015 M 6000

Бренды по названию

Популярные бренды

Arctic Cat 2015 M 6000, Руководство оператора

Результаты поиска

Содержание 2015 M 6000

Отзывы:

Похожие инструкции для 2015 M 6000

Бренды по названию

Популярные бренды