Arctic Cat 2014 Prowler HDX Скачать руководство пользователя страница 138

Страница: 138 / 192

135

RESISTANCE



NOTE: For these tests, the meter selector should

be set to the OHMS position.

Primary Winding

1. Connect the red tester lead to the terminal (with the

wire removed); then connect the black tester lead to

ground.

PR278A

2. The meter reading must be within specification.

Secondary Winding

1. Connect the red tester lead to the high tension lead

(with the plug cap removed); then connect the black

tester lead to either primary terminal.

2. The meter reading must be within specification.



NOTE: If the meter does not show as specified,

replace ignition coil.

Spark Plug Cap

1. Connect the red tester lead to one end of the cap;

then connect the black tester lead to the other end of

the cap.

AR603D

2. The meter reading must be within specification.



NOTE: If the meter does not show as specified,

replace the spark plug cap.

VOLTAGE

Primary Coil

1. Set the meter selector to the DC Voltage position;

then disconnect the two wires from the coil.



NOTE: The coil is located to the right of the

engine and may be accessed from behind the
right-side seat with the cargo box raised.

2. Connect the red tester lead to the orange wire and the

black tester lead to the blue/white wire.

3. Turn the ignition switch to the ON position. The

meter must show battery voltage.

EFI Sensors/Components

CRANKSHAFT POSITION (CKP)
SENSOR

To test the CKP sensor, see Stator Coil/Crankshaft Posi-

tion (CKP) Sensor in this section.

OXYGEN (O2) SENSOR

The Oxygen Sensor (O2 Sensor) is located in the exhaust pipe.



NOTE: When testing the resistance of the sensor’s

heater, the engine/exhaust pipe must be at room tem-
perature (65-75° F) or inaccurate readings will occur.

1. Open the cargo box; then remove the seat, air filter

cover, and air filter.

2. Remove the backrest and seat base.

3. Disconnect the sensor.

HDX 247



NOTE: For this test, the meter must be in OHMS

position.

5. On the sensor side of connector, connect the black (nega-

tive) test lead to one white wire pin; then connect the red

(positive) test lead to the other white wire pin. Readings

should be between 6.7 and 10.1 ohms.



NOTE: If the meter does not read as specified,

replace the sensor.

CAUTION

Always disconnect the battery when performing resis-
tance tests to avoid damaging the multimeter.

Содержание 2014 Prowler HDX

































































































































































































Результаты поиска

Содержание 2014 Prowler HDX

Отзывы:

Бренды по названию

Популярные бренды

Arctic Cat 2014 Prowler HDX, Руководство по обслуживанию

Результаты поиска

Содержание 2014 Prowler HDX

Отзывы:

Бренды по названию

Популярные бренды