Aquant BLM100 Скачать руководство пользователя

Страница: 26 / 26

Heat pump runs

but does not heat

Verify cold air is blowing out the top of the heat pump. If the heat

pump has just been installed or if the pool water has been allowed

to cool significantly, it is necessary to run the heat pump

continually, it is necessary to run the heat pump continually for

24-48 hours. If the heat pump has been in operation for some

time, increase the circulating pump time, or switch the control

board to Maintain Heat function. If heating a spa, verify no air

intake stand pipes are open. If heat pump still does not heat, call

for service.

Heat

pump

leaking water

Possible heat exchanger or plumbing leak. Turn the heat pump

off, then turn circulating pump off for at least one hour to see if the

water leak stops. If the water leak stops. Normal condensation is

occurring. If the water leak continues, after the heat pump is shut

off for at least one hour, call for service.

Содержание BLM100



























Результаты поиска

Содержание BLM100

Отзывы:

Похожие инструкции для BLM100

Бренды по названию

Популярные бренды

Aquant BLM100, Инструкция по установке и эксплуатации

Результаты поиска

Содержание BLM100

Отзывы:

Похожие инструкции для BLM100

Бренды по названию

Популярные бренды