background image

Aquarian Thermo 

installation instuctions

page 7

Remove the gripper ring assembly from the 

rear of the back plate and ensuring correct 

alignment of the gripper rings, slide over the

projecting pipes flush to the wall face. 

Cut the supply pipes to their finished length

(18mm – 21mm) using a rotary type cutter.

5

Briefly run the hot and cold supplies to flush out any debris that may be 

present in the system.

6

Remove the two fixing screws to release the lower shroud assembly from the

back plate. Carefully remove and set aside. 

4

If the valve is being installed for use with a gas

fired instantaneous (multipoint) water heater 

or a combination boiler, the cold water flow 

regulator must be fitted at this stage by

insertion into the cold water port.

(The flow regulator is supplied in its own pack). 

Remove the four cartridge fixing screws and

carefully detach the cartridge assembly from the back plate. Fit the flow 

regulator into the cold port fully home, with the central O’ ring facing the

incoming flow. A small length of 15mm pipe may used to facilitate the 

installation of this regulator. Refit the cartridge to the back plate using the

four fixing screws ensuring the hot and cold markings on the cartridge are

uppermost.

7

Run a thin bead of silicone sealant in the mastic groove of the back plate.

Using a silicone based lubricant, lubricate the projecting pipe ends before

carefully pushing the shower valve into position fully home. Secure using the

screws provided. 

8

Содержание Aquarian Thermo




















Отзывы: