background image

 

 

!

WARNING:

 Check the data plate on this unit before installation. Connect the unit only to the voltage 

and frequency listed on the data plate. Connect only to 1 or 3 phase as listed on the data plate.

!

 

!

!

WARNING:

 Disconnect device from electrical power supply and place a Tag Out-Lockout on the 

power plug, indicating that you are working on the circuit.

 

!

  

 

 

 

!

CAUTION: 

Maintenance & repair should be handled by a factory authorized agent. Before doing 

any maintenance or repair, contact APW Wyott.

!

 

  

 

 

 

!

NOTICE:

 

Install according to the spacing requirements listed in the installation section of 

this manual. We strongly recommend having a competent professional install this 
equipment. A licensed electrician should make the electrical connections and connect 
power to the unit. Local codes should always be used when connecting these units to 
electrical power. In the absence of local codes, use the latest version of the National 
Electrical Code.

 

CONTENTS 

 

Description 

Page 

Description 

Page 

 

Safety Precautions………….………..  2 

Exploded Views ………………………… 7 

 

Specifications..............................….... 4 

Parts List……….………………………... 9 

 

General Installation Instructions……  4 

Wiring Schematics ……………………..  11 

 

Cleaning .……………………….…….. 5 

Notes…………………………………….  12 

 

 

Troubleshooting / Service ...……….... 5 

Warranty…………………………………  13 

 

 

Operation…………………...……….... 6 

 

 
 

 

 
 
LOCATION OF DATA PLATE 

The data plate for the SPTU is located on the back of the unit. 
 

 
 
IMMEDIATELY INSPECT FOR SHIPPING DAMAGE 

All containers should be examined for damage before and during unloading. The freight carrier has 
assumed responsibility for its safe transit and delivery. If equipment is received damaged, either apparent 
or concealed, a claim must be made with the delivering carrier. 

A)  Apparent damage or loss must be noted on the freight bill at the time of delivery. It must then be 

signed by the carrier representative (Driver). If this is not done, the carrier may refuse the claim. 
The carrier can

 

supply the necessary forms. 

B)  Concealed damage or loss if not apparent until after equipment is uncrated, a request for 

inspection

 

must be made to the carrier within 15 days. The carrier should arrange an inspection. 

Be certain to hold all contents and packaging material. 

 
Installation and start-up should be performed by a qualified installer who thoroughly read, understands 
and

 

follows these instructions. 

 

 

Содержание SPTU- 50














Отзывы: