manualshive.com logo in svg

Applied Instruments XR-3, Руководство по эксплуатации

Поделиться
Скачать
Applied Instruments XR-3 Скачать руководство пользователя страница 61

XR-3 TS2 Module Operation Manual 

 

XR-3 

 

Page 61 of 66 

6)  Attempting to turn on a unit when the battery contains insufficient charge may result in 

beeps and/or a flash on the LCD but will not harm the unit. 

AC Power 

When 110VAC or 220VAC power is applied via the external AC to DC switching power supply, it 
supplies 14VDC power to charge the battery, run the meter, and power the LNB.  In this case, the 
power available to the LNB is limited to 750 mAmps to avoid overdriving the power circuit and the 
battery charging circuit. 

DC Power 

When external 12VDC power is provided from a vehicle, it supplies enough power only to charge 
the battery. 
 
 

16. Troubleshooting / FAQs 

 

a)  I receive an error message stating: “Error: LNB under voltage, over current, or short” 

i)  Replace top (Signal In port) F-connector barrel.  Use a 7/16" wrench to loosen 

existing barrel.  Install new F-connector barrel and only tighten to 20 inch pounds of 
torque with wrench after finger-tightening.  Warning: Do NOT over-tighten! 

ii)  Ensure that you have the latest available version of Field Guide and Software loaded.  

If you don't, you must update meter's software using the FlashUpdate program. 

iii)  If issue still remains, contact Applied Instruments' Tech Support department and 

request a RMA# to send the instrument to the factory for inspection and repair. 

 

b)  While I have the LNB connected to the ODU / LNB port of the meter with a coax cable 

and the LNB power is turned on, I don't even see any signal level shown on left bar 
graph.  It just says "UNDER".   
i)  Replace top (Signal In port) F-connector barrel.  Use a 7/16" wrench to loosen 

existing barrel.  Install new F-connector barrel and only tighten to 20 inch pounds of 
torque with wrench after finger-tightening.  Warning: Do NOT over-tighten! 

 

c)  While attempting to perform a Limit Scan, I receive an Error message saying "ERROR: 

Key transponder not found or invalid". 
i)  Turn the meter off and on.  Then go to MENU/OPTIONS and press the PRESET soft-

key in the lower left corner of the LCD screen.  Then exit back to the MAIN MENU 
and try to run your Limit Scan again. 

 

d)  I believe my dish is properly aligned, but I'm not getting a LOCK on the meter for the 

desired satellite. 
i)  Ensure that you have the latest available version of Field Guide and Software loaded.  

If you don't, you must update meter's software using the FlashUpdate program. 

ii)  Ensure that you are using the proper LNB type and that you have specified the 

correct LNB type in the System Setup software menu.  If in doubt, refer to the label or 
tag on the body of the LNB and contact Applied Instruments' Tech Support 
department to consult with them. 

iii)  If the incoming signals are linearly polarized, you must ensure that you have properly 

adjusted the polarization offset of the LNBF or feed horn assembly.  Even if the 
antenna reflector is set to the proper azimuth and elevation, it is possible to not 
receive adequate signal if your polarization offset is very far off. 

iv)  If you're working with circularly polarized signals on a multi-LNB dish assembly, you 

must ensure that the skew/tilt of the dish is set correctly.  You can use the ZIP postal 
code lookup feature to obtain approximate tilt/skew settings. 

 

TESCOM USA

TESCOMUSA.COM

Содержание XR-3



































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды