manualshive.com logo in svg

Applied Instruments XR-3, Руководство по эксплуатации

Поделиться
Скачать
Applied Instruments XR-3 Скачать руководство пользователя страница 17

XR-3 TS2 Module Operation Manual 

 

XR-3 

 

Page 17 of 66 

5. Options 

 
There are several options you may select to personalize the operation of your meter. 
 

 

 
To use this screen, highlight the option you want to change with the up/down arrow keys and 
select the value you want with the left/right arrow keys.  Press EXIT soft-key when done. 

Signal Level 

The signal level may be displayed in dBm, dBmV or dBµV.   

Signal Quality 

The signal quality number may be displayed as one of the following: 

C/N (carrier to noise ratio) in dB 
IRD (receiver) equivalent number 

 Eb/N

 – Energy per bit over noise energy per hertz in dB 

 Es/N

 – Energy per symbol over noise energy per hertz in dB 

 
IRD numbers for DIRECTV

 range from 0 to 100.  Dish Network

 uses two scales: the old scale 

from 0 to 125 and a new scale with much lower values (approximately 0 to 85). 

Frequency 

The frequency may be displayed as either the L-band frequency, which the meter is tuned to, or 
the downlink frequency transmitted by the satellite.  Both are displayed in MHz.  The L-Band 
(900-2150 MHz) frequency is the frequency of the signal after being down-converted by the LNB. 

Sounder Option 

Peaking via the audible tone can be done in two ways:  “tone-on-lock” and “peak-o-matic”.  The 
“tone-on-lock” method uses the following: 
 
1)  Slow beep - the function is on 
2)  Fast beep – the signal is locked 
3)  Solid – the signal is locked and at the highest level yet seen 
 

TESCOM USA

TESCOMUSA.COM

Содержание XR-3



































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды