manualshive.com logo in svg

Applied Instruments XR-3, Руководство по эксплуатации

Поделиться
Скачать
Applied Instruments XR-3 Скачать руководство пользователя страница 41

XR-3 TS2 Module Operation Manual 

 

XR-3 

 

Page 41 of 66 

Scanning 

Selecting “Limit Scan” from the Main Menu will start the Limit Scan screen.  If limits have already 
been defined for the presently selected satellite, the scanning will start immediately. The Limit 
Scan is only useful if the LNB is being powered by the meter. Press the LNB soft-key (located 
near middle right area of screen) to power the LNB. On a multi-LNBF setup, press the LNB soft-
key more than once to toggle from LNB1 to LNB2 to LNB3, etc. The satellite orbital position (i.e. 
110.0W) related to each selected LNB port will be displayed in the top right corner of the LCD 
screen. 
 

 

 
For each transponder to scan, the screen shows: 

1)  Tr – The transponder numbers to be scanned (transponders must be defined by user) 
2)  dBm – The measured signal level value corresponding to each specified transponder (will 

either be displayed in dBm, dBmV, or dBµV, depending on your chosen signal level 
values in the Options menu) 

3)  IRD – The measured IRD signal quality value corresponding to each specified 

transponder 

4)  A transponder grade next to each individual transponder: 

a.  FAIL - Below the minimum Signal Level limit or below the minimum IRD Signal 

Quality limits 

b.  Low - At or above the minimum Signal Level limit and at or above the minimum 

Signal Quality limits but below the average Signal Quality limits 

c.  Good - At or above the minimum Signal Level limit and at or above the average 

Signal Quality limits 

5)  Summary of Limit Scan results - At the bottom of the screen, the user will see a 

comparison to the minimum first (top row at bottom of screen) and the comparison to the 
average second (bottom row at bottom of screen).  Possible Limit Scan summary 
messages that could be displayed at bottom of screen: 

a.  All Above Min – the measured IRD Signal Quality and Signal Level of all 

transponders tested are above the minimum limits 

b.  Some Below Min – the measured IRD Signal Quality or Signal Level of at least 

one of the transponders tested is below the minimum limit 

TESCOM USA

TESCOMUSA.COM

Содержание XR-3



































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды