manualshive.com logo in svg

Applied Instruments XR-3, Руководство по эксплуатации

Поделиться
Скачать
Applied Instruments XR-3 Скачать руководство пользователя страница 26

XR-3 TS2 Module Operation Manual 

 

XR-3 

 

Page 26 of 66 

Custom Transponder Parameters Fields editable by you: 

  Orbit - Specify orbital location of satellite.  For satellites located west of the Prime 

Meridian, type a “-“ in front (i.e. -89.0 for 89.0°W) 

  Sat - Specify name of satellite (i.e. Galaxy 28) 

  Label - Specify transponder label (i.e. Tr 5) 

  Freq - Specify frequency of transponder (i.e. 12149.625).* 

  Polar - Using Left or Right arrow buttons, specify polarization of transponder (i.e. 

Horizontal or Vertical or Left or Right) 

  Sig Type - Using Left or Right arrow buttons, specify signal type (i.e. DVB-S, DVB-S2, 

DC2, Turbo, T-ACM, DTV-S2, Other, or DSS) 

  Code rate – For Turbo or DVB-S2 signal types, using Left or Right arrow buttons, specify 

Code Rate / FEC (i.e. Auto or 1/2 or 2/3 or 3/4) 

  Sym rate - Specify Symbol Rate (i.e. 2010 kSym) 

  Pilot – For DVB-S2 signals, after you’ve specified a custom code rate, using Left or Right 

arrow buttons, specify Pilot status (i.e. AUTO or OFF or ON) 

  Optns – For DC2 signals, specify options relevant to the transponder (i.e. Split I, Split Q, 

Orth, Orth/I, Orth/Q, or None) 

  Id - Using Left or Right arrow buttons, specify if you want this custom transponder to be 

used as an ID transponder for ID verification check on the satellite.** 

 
*It is best to specify the downlink frequency (frequency direct from the satellite before down-
conversion by LNB).  If you wish to specify the L-Band frequency (frequency of the transponder 
after down-conversion by LNB), then press the "DN LINK" soft-key (located near top right corner 
of LCD screen) and you will see the soft-key label change to "IF Freq".  Then enter the L-Band 
frequency.  The meter will then calculate the downlink frequency based on your present LNB LO 
settings that have been defined in the System Setup menu.  Modems often display the L-Band 
frequency of the carrier, but for this information to be useful, you must specify the LO frequency 
of the LNB in use for that system. 
 
**If there is already an ID transponder for the satellite in the meter's database, then the custom 
transponder would become a 2nd ID transponder used for an additional level of checking.  If there 
is not presently an ID transponder for the satellite in the meter's database, then the custom 
transponder would become the default transponder and sole ID transponder for that satellite. 
 
***Remember that the XR-3 satellite meter is only designed to measure the downlink / receive / 
outbound signal.  Please do not enter any transponder parameters for the uplink / transmit / 
inbound signal, as the parameters will not be of any utility in the meter. 
 

  Press “Save” to save the changes or the new transponder parameters. 

  Press the "EXIT" soft-key (located near bottom right corner of LCD screen) if you wish to 

exit the Custom Transponders editing screen without saving the changes or new 
transponder parameters. 

  The custom transponders will appear in the meter as if they are part of the Field Guide.  

As such, they will be usable and viewable in the Limit Scan and Proof of Performance 
(PoP Scan) features. 

  You can save up to 256 custom satellite transponders in the meter. 

  If the custom transponder is not visible to the selected LNB and feed horn configuration, it 

won’t appear (i.e. If you define a horizontal transponder and select a circular feed horn in 
the System Setup menu then you won’t see it displayed.  If you define a C-Band 
transponder and select a Ku Band LNB in the System Setup menu then you won’t see it 
displayed) 

  Custom transponders do not have any beam/footprint info so they are considered visible 

in all geographic regions and therefore will appear in the meter, regardless of which 

TESCOM USA

TESCOMUSA.COM

Содержание XR-3



































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды