background image

 

  

6

 

 

1. Next, position the T100 Turbo Unit as far away as practical and possible from the area where you 

will spray. 

2. Attach the remaining end of the hose to the T6000 Spray Gun as follows: 

a. Locate the coupler at the rear top of the T6000 Spray Gun. See T6000 diagram. 
b. Pull back on the collar of the black connector on the air hose. 
c. Push the connector over the coupler and release. Figure 7. 
d. Your Spray Gun should now be firmly attached to the air hose. 

 

Using Your Apollo T6000 Spray Gun  

 

 

Your Apollo T6000 spray gun is certified by Apollo Sprayers. This means your spray gun only uses 

about 3 PSI and is genuine HVLP.  There are many small passageways for the air to travel inside the 
spray gun.  If one of these air passages becomes blocked, or build-up of material starts to occur, your 
spray pattern will become distorted, therefore, always keep your spray gun clean. Your Apollo T6000

 

spray gun comes fitted with a custom tanning needle and nozzle specifically designed for spraying 
tanning solutions. Using this size tip/nozzle and needle you can achieve from a 1/4" line up to a 6" 
wide fan pattern.  To do this, rotate the Air Cap (#2) to the desired fan pattern type, then open the 
solution flow screw (#10) counter-clockwise and move the spray gun closer or further away from your 
work piece until you get the desired width of pattern.   The closer you are to the clients body the 
smaller the fan.  The farther back you hold the spray gun from the clients body the larger the fan 
pattern will be.  A little practice will enable you to master this technique in no time flat!  Never hold the 
spray gun more than 6-8” away from the client. 

 

PRACTICE: 

 

 

 

VERY IMPORTANT!! 

To fill the cup with solution hold the black cup lid tight and remove the cup from 

your spray gun

. DO NOT HOLD THE SPRAY GUN HANDLE AND REMOVE THE CUP.

  Fill the cup 

approximately half way with some water. Hold the black lid assembly

 

and re-attach the cup to the 

body of the spray gun and hand tighten to create a good seal. Attach the spray gun to the air hose. 
Attach the other end of the air hose to the turbine unit.  Turn the turbine unit on. 

You will notice air 

is now flowing through the air cap all the time, this is normal and correct.

 Position the air cap 

(#2) in the horizontal or vertical position, turn the solution flow screw (#10) clockwise until closed. 
Now open the solution screw slowly until you have it open 1 full turn.  Point the spray gun away from 
yourself (and anyone else) and pull the trigger all the way back. You should see a “V” shaped mist (or 
triangle) called a fan pattern. Now, with the trigger depressed, if you turn the material flow screw, 
(#10) clockwise (closing) making very small adjustments at a time, you will notice that the fan pattern 
is beginning to get smaller. Now, reverse this and notice the pattern will get larger. Take a large piece 
of cardboard and direct the pattern at the surface, hold the spray gun approximately 6" from the 
surface.  Pull the trigger. Observe the outline and size of the pattern. Now, turn the solution flow 
screw clockwise (closing). Move the spray gun an inch or two closer to the surface. Pull the trigger. 
Notice the pattern has become smaller. You can continue reducing the solution flow and move the 
spray gun even closer to the surface and the pattern will continue to get smaller and smaller. Next, 
rotate the air cap to a diagonal position (See Spray Patterns, Pg. 5). Vary the solution flow and the 
distance of the spray gun from the work surface. Notice the change in pattern size.  

 

  

 

Содержание Mighty-Mist T6000











Отзывы: