Aplex APC-3296P Скачать руководство пользователя страница 64

Страница: 64 / 113

APC-3296P User Manual

SATA Controller(s)

This field is used to enable or disable Serial ATA devices.

SATA Mode Selection

The mode selection determines how the SATA controller(s) operates.

AHCI Mode

This option allows the Serial ATA devices to use AHCI (Advanced Host Controller

Interface).

RAID Mode

This option allows you to create RAID or Intel Matrix Storage configuration on Serial
ATA devices.

Serial ATA Port 0, 1 and 2

This field is used to enable or disable the serial ATA port.



USB Configuration

This section is used to configure the parameters of the USB device.

USB BIOS Support

Disabled

Disable USB keyboard/mouse/storage support.

Enabled

Enable USB keyboard/mouse/storage support under UEFI and DOS environment.

UEFI Only

Enable USB keyboard/mouse/storage support only under UEFI environment.

Содержание APC-3296P


















































































































Результаты поиска

Содержание APC-3296P

Отзывы:

Похожие инструкции для APC-3296P

Бренды по названию

Популярные бренды

Aplex APC-3296P, Руководство пользователя

Результаты поиска

Содержание APC-3296P

Отзывы:

Похожие инструкции для APC-3296P

Бренды по названию

Популярные бренды