APB-DynaSonics ProDesk-4 Скачать руководство пользователя страница 3

ProDesk-4 OWNER’S MANUAL

3

IMPORTANT SAFTEY INSTRUCTIONS

1)

 

Read These Instructions

2)

 

Keep These Instructions

3)

 

Heed All Warnings

4)

 

Follow All Instructions

5)

 

Do Not Use this Apparatus near water

6)

 

WARNING: To reduce the risk of fire or electric shock, do not expose this apparatus to rain or
moisture. Do not expose the apparatus to dripping or splashing. Do not place objects
containing liquids, such as vases, on the apparatus.

7)

 

For safety the AC supply must include third wire protective ground connection.

8)

 

Do not block any ventilation openings at the front and rear. Install in accordance with the
manufacturer’s instructions.

9)

 

Do not install near any heat sources such as radiators, heat registers, stoves or other apparatus
(including amplifiers) that produce heat.

10)

 

Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has
two blades with one wider than the other. a grounding type plug has two blades and a third
grounding prong. The wide blade or the third prong is provided for your safety. If the provided
plug does not fit your outlet consult an electrician for replacement of the obsolete outlet.

11)

 

Protect the power cord from being walked on or pinched particularly at plugs convenience
receptacles and the point where they exit the apparatus.

12)

 

Unplug this apparatus during lightning storms or when unused for long periods of time.

13) Refer all servicing to qualified service personnel. Servicing is required when the apparatus has

been damaged in any way, such as power supply cord or plug is damaged, liquid has been
spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or
moisture, does not operate normally or has been dropped.

Содержание ProDesk-4









































Отзывы: