AOR AR6000 Скачать руководство пользователя страница 29

Страница: 29 / 95

The pre-programming of step size may be manually overridden so you may choose alternative settings

at will or when band plans are updated.

If you wish to change the default tuning frequency step, press the [

STEP]

key. The LCD will display the

current frequency step and the blinking “STEP” while waiting for the new parameter. Use the sub dial to

select the desired step.

To accept the displayed tuning step size, press the [

MHz

] key.

The tuning step size may also be programmed in 1 Hz (2 Hz over 3.15 GHz) (via the keypad) so that

unusual step sizes other than those stated are possible. The acceptable step size range is less than 1 MHz

in 1 Hz steps (or 2 Hz over 3.15 GHz).

3-8 IF BANDWIDTH

The IF bandwidth selects how SELECTIVE the receiver will be when monitoring signals off air. However,

it is not simply a case of using the narrowest filter at all times; particular modes require differing amounts

of bandwidth in order to operate. Otherwise the receive system will not produce intelligible sound.

Correct receive mode and IF bandwidth must always be selected for optimum reception. If the bandwidth

selection is too narrow, distortion or signal break-up may occur. If the bandwidth selection is too wide,

adjacent interference may be encountered. For this reason, a selection of IF filter bandwidths are provided

as standard.

Содержание AR6000
































































































Результаты поиска

Содержание AR6000

Отзывы:

AOR AR6000, Руководство по эксплуатации, Страница: 29 / 95

Результаты поиска

Содержание AR6000

Отзывы: