AOpen AP5C Скачать руководство пользователя страница 73

Страница: 73 / 76

AMI BIOS

3-34

User’s Guide

NCR SCSI BIOS and Drivers

The NCR 53C810 SCSI BIOS resides on the same flash memory

chip as the system BIOS. To use the onboard NCR BIOS, you need

to install an NCR 53C810 SCSI controller card in your system.

All SCSI devices that you install in your system require software

drivers. The NCR SCSI BIOS directly supports SCSI hard disks

under DOS, Windows and OS/2. It also uses DOS-format and SCO

UNIX-format support floppy disk device drivers that come with the

NCR 53C810 SCSI controller card. The DOS-format device drivers

are for SCSI devices used with DOS, Windows NT, Novell NetWare

and OS/2.

The SCO UNIX-format device drivers are for SCSI

devices used with SCO UNIX.

These drivers offer higher

performance than the direct BIOS support.

To use the device drivers, you must install them in your system hard

disk drive and add them to your system configuration files. For

detailed installation instructions, see the README files that come

with the drivers.

The  system  board  also  supports  the  AMI
Flash  Memory  Writer  Utility  that  allows
you  to  upgrade  the  system  BIOS.  For
more  information  on  this  utility,  contact
your local distributor.

Содержание AP5C













































































Результаты поиска

Содержание AP5C

Отзывы:

Бренды по названию

Популярные бренды

AOpen AP5C, Руководство пользователя

Результаты поиска

Содержание AP5C

Отзывы:

Бренды по названию

Популярные бренды