AOpen AP5C Скачать руководство пользователя страница 59

Страница: 59 / 76

AMI BIOS

3-20

User’s Guide

16-bit I/O Recovery Time

This parameter allows you to set the response time of the 16-bit I/O

connected to your system. The range is from 1~4 SYSCLK. The

default setting is

1 SYSCLK.

PCI Control

VGA Palette Snooping

PCI devices support the “palette snooping” technique that enables

the device to control access to their palette registers.

Set this parameter to

Enabled

to activate the palette snooping

function in the PCI VGA devices installed in your system.

PCI-IDE Card Selection

This parameter allows you to select the PCI-IDE card that you want to

enable. The board can support a maximum of four PCI-IDE cards.

The available selections are Slot 1, Slot 2, Slot 3, Slot 4, and Absent.

Select

Absent

if you do not have any PCI card installed.

PCI Primary IDE INT# Line

This parameter lets you assign an INT for the IDE device connected

to your primary IDE connector. The settings are INT A, INT B, INT C,

INT D, Absent and Not Used. If you do not have any PCI IDE card

installed in your system and your PCI IDE Card Selection parameter

setting is

Absent

, this parameter becomes non-configurable.

Содержание AP5C













































































Результаты поиска

Содержание AP5C

Отзывы:

Бренды по названию

Популярные бренды

AOpen AP5C, Руководство пользователя

Результаты поиска

Содержание AP5C

Отзывы:

Бренды по названию

Популярные бренды