AOpen AP5C Скачать руководство пользователя страница 51

Страница: 51 / 76

AMI BIOS

3-12

User’s Guide

32-bit Mode

Enabling this function improves the hard disk performance by

increasing the data transfer rate from 16-bit to 32-bit.

Primary 1st LBA Mode

This enhanced IDE feature allows you to use a hard disk with a

capacity higher than 528 MB. This is made possible through the

Logical Block Address (LBA) mode translation.

This parameter

affects the primary IDE hard disk drive connected to the IDE 1

connector. The default setting is

Disabled

Primary 2nd LBA Mode

This enhanced IDE feature allows you to use a hard disk with a

capacity higher than 528 MB. This is made possible through the

Logical Block Address (LBA) mode translation.

This parameter

affects the secondary IDE hard disk drive connected to the IDE 1

connector. The default setting is

Disabled

Secondary 1st LBA Mode

This enhanced IDE feature allows you to use a hard disk with a

capacity higher than 528 MB. This is made possible through the

Logical Block Address (LBA) mode translation.

This parameter

affects the primary IDE hard disk drive connected to the IDE 2

connector. The default setting is

Disabled

Содержание AP5C













































































Результаты поиска

Содержание AP5C

Отзывы:

Бренды по названию

Популярные бренды

AOpen AP5C, Руководство пользователя

Результаты поиска

Содержание AP5C

Отзывы:

Бренды по названию

Популярные бренды