AOpen AP5C Скачать руководство пользователя страница 17

Страница: 17 / 76

Features

1-6

User’s Guide

Super I/O Controller

The onboard super I/O controller chip SMC37C665GT supports two

UART 16450/16550-compatible serial ports and a parallel port (SPP,

EPP, ECP)

. It also accommodates 1.2-/1.44-/2.88-MB disk drives

allowing full-range access to 5.25-inch drives with 360-KB or 1.2-MB

format and 3.5-inch drives with 720-KB, 1.44-MB or 2.88-MB format.

Keyboard Connector

The keyboard connector at the rear of the system board allows you to

connect any AT-compatible keyboard. PS/2 keyboard and mouse

connectors are optional.

SRAM

The system board supports 256-KB and 512-KB second-level, write-

back cache.

Power Management

The AP5C features a system power-management mode that

conforms to the power-saving standards of the U.S. Environmental

Protection Agency (EPA) Energy Star program. See Chapter 3 for

more information on the power-management mode.

SPP: Standard Parallel Port
EPP: Enhanced Parallel Port (IEEE 1284 compliant)
ECP: Extended Capabilities Port (IEEE 1284 compliant)

Содержание AP5C













































































Результаты поиска

Содержание AP5C

Отзывы:

Бренды по названию

Популярные бренды

AOpen AP5C, Руководство пользователя

Результаты поиска

Содержание AP5C

Отзывы:

Бренды по названию

Популярные бренды