background image

CAUTION!

Never touch the device during operation!

The housing may heat up!

C

CAUTION!

N

Never look directly into the light source,

A

As sensitive persons may suffer an epileptic shock.

Please be aware that damages caused by manual modifications to be the device are
not subject to warranty. Keep away from children and non-professionals.

CLEANING AND MAINTENANCE

1. To reduce the risk of electrical shock or fire, do not expose this unit to rain or moisture.
2. Do not spill water or other liquids into or on to your unit.
3. During long periods of non-use, disconnect the unit’s main power.
4. It should be installed in a well-ventilated place, at a distance of 50 centimeters or more
with the walls. At the same time, please check if the fan and ventilation holes are
unobstructed.

The following points have to be considered during the inspection
1) All screws for installing the devices or parts of the device have to be tightly connected

and must not be corroded.

2) There must not be any deformations on the housing. Fixations and installations

spots(ceiling, suspension, trussing).

3) Mechanically moved parts must not show any traces of wearing and must not rotate

with unbalances.

4) The electric power supply cables must not show any damage, material fatigue or

sediments. Further instructions depending on the installation spot and usage have to
be adhered by a skilled installer and any safety problems have to be removed.

CAUTION!

Disconnect from mains before starting maintenance operation!

In order to make the lights in good condition and extend the life time, we suggest a regular
cleaning to the lights.
1) Clean the inside and outside lens each week to avoid the weakness of the lights due

to accumulation of dust.

2) Clean the fan each week.
3) A detailed electric check by approved electrical engineer each three month, make sure

that the circuit contacts are in good condition, prevent the poor contact of circuit from
overheating.

We recommend a frequent cleaning of the device. Please use a moist, lint-free cloth.
Never use alcohol or solvents.

Содержание ALED BSW CMY 400




















Отзывы: