Anywire ASLINK BL296 B-08F V50 Series Скачать руководство пользователя страница 1

Страница: 1 / 22

-BL296*B08F****V50 1/22-

BL296

□

B-08F

□□□□

-V50

Ver.1.1

AnyWireASLINK System Products Guide

PNP input

PNP output

PNP input/PNP output

NPN input

NPN output

Euro
terminal block

NPN input/NPN output

PNP input

PNP output

PNP input/PNP output

NPN input

NPN output

Spring
terminal block

NPN input/NPN output

PNP input

PNP output

PNP input/PNP output

NPN input

NPN output

Standard
terminal block

NPN input/NPN output

A WARNING indicates a potentially hazardous

situation which, if not handled correctly, could

result in death or serious injury.

Precautions that must be observed in order to use this system safely are indicated as shown below.

You must observe these precautions.

[Notes on Safety]

A CAUTION indicates a potentially hazardous situation

which, if not handled correctly, may result in personal

injury or property damage.

[Type]

ASLINKTERMINAL

[ASLINK Terminal with Compact Terminal Block]

CAUTION

WARNING

○

System power supply

Use a stable, 24V DC power supply. Use of an unstable power supply may cause problems with the system.

○

Separately route high-voltage and power cables

Although the AnyWireASLINK has a high noise margin, install the transmission line and I/O cables away from high-voltage and power cables.

○

Connectors and terminals

- Pay careful attention to the length and installation of cable wiring to ensure that connectors and cables are neither overloaded nor disconnected.
- Make sure to prevent any metal objects from getting inside the connectors or the terminal blocks.
- Short-circuits caused by metal objects or mis-wiring are likely to damage the device.

○

Do not impose any external loads on the units. Doing so may cause a failure.

○

Do not disconnect or reconnect between the transmission line and slave units when the transmission line is active. A malfunction may occur.

○

Use the AnyWireASLINK within the range of the specifications and conditions shown below.

○

System Safety

This system is intended for general industrial applications. It does not have functions for supporting applications requiring higher

levels of safety such as safety-related devices or accident prevention systems. The product must not be used for these purposes.

○

Always turn off the power in installing or replacing the system.

○

Prolonged continuous flow of a rated load current or higher or a transit current due to load short-circuit, etc., in the hybrid unit including
the output unit and the output circuit may result in smoking or firing. An external safety device such as a fuse must be installed.

CAUTION

WARNING

■

Note on use

⇒

A separate Address Writer is required to set addresses and other data.

For more information, refer to [Various Settings] on page 12.

Euro terminal
block type

[Warranty]

■

Warranty period

The warranty on the delivered Product shall continue to be effective for one (1)

year after the delivery thereof to a location as designated by the original owner.

■

Scope of warranty

Should a defect occur in any part of the Product during the foregoing warranty

period when it is used normally in accordance with the specifications described
in this Products Guide, the Company shall replace or repair the defect free of
charge, except when it arises as a result of:

  [1] Misuse or abuse of the Product by the owner;
  [2] Fault caused by other than the delivered Product;
  [3] The unauthorized modification or repair of the Product by any person other

than the Company’s personnel;

[4]

Any unusual force of nature, disaster or other cause beyond the Company’s control.

The term “warranty,” as used herein, refers to the warranty applicable to the

delivered product alone. The Company shall not be liable for consequential or
incidental damages resulting from any malfunction.

■

Repair at cost

After the expiration of the warranty period, the owner shall be responsible for all

costs and expenses incurred for the troubleshooting and repair of the Product. Even
during the warranty term, the Company shall repair any defects arising from causes
other than within the scope of the warranty as specified above, at the owner’s cost.

■

Changes in the product specifications and the descriptions in the manual

The descriptions in this manual may be subject to change without notice.

[About Pictogram

]

Ver. 1.0

Compatible with

Ver. 1.1

1 The pictogram may not be marked (or stuck) depending on the product.

2 AnyWireASLINK device not compatible with Ver. 1.1 (word transmission and

single unit simplified replacement functions)

Some products, not marked with the Ver. 1.1 pictogram, are compatible with
the functions included in Ver. 1.1. Refer to the lot No. and the product guide
for ultimate confirmation.

3 For details of Ver. 1.1, refer to the subsequent pages.

BL296SB-08FS-11-V50

BL296PB-08FS-11-V50

BL296XB-08FS-11-V50

BL296SB-08F-11-V50

BL296PB-08F-11-V50

BL296XB-08F-11-V50

BL296SB-08FS-3-V50

BL296PB-08FS-3-V50

BL296XB-08FS-3-V50

BL296SB-08F-3-V50

BL296PB-08F-3-V50