Anybus AWB5011 Скачать руководство пользователя

Страница: 111 / 126

Maintenance and Troubleshooting

109 (124)

7.2.2

TFTP Backup and Restore

In the TFTP Server mode, the switch acts as TFTP client.

Fig. 92

RFTP Backup and Restore

Ensure that the TFTP server is ready.

TFTP Server IP

Enter the TFTP Server IP address.

File Name

Enter the file name of the configuration file.
File format:

.conf

Configuration File The configuration file of the switch is a pure text file.

The file can be modified, add/remove the configuration settings, and then restored back to the
switch.

Action

Select Load or Save configuration.
Click

Submit

7.2.3

USB Backup and Restore

In the USB Mode, you can Load Setting from File or Save Setting to USB.

File format:

.conf

Fig. 93

USB Backup and Restore

Connect a USB memory to the switch.

To restore the settings from a configuration file: Click

Restore

and then browse and load the

backup configuration file from the USB memory.

To save the settings in a configuration file to the USB memory: Click

Save to USB

Anybus

Managed Industrial L3 Switch User Manual

SCM-1202-151 1.1 en-US

Содержание AWB5011































































































































Результаты поиска

Содержание AWB5011

Отзывы:

Похожие инструкции для AWB5011

Бренды по названию

Популярные бренды

Anybus AWB5011, Руководство пользователя

Результаты поиска

Содержание AWB5011

Отзывы:

Похожие инструкции для AWB5011

Бренды по названию

Популярные бренды