Antunes Roundup VCT-2000 Скачать руководство пользователя страница 28

Страница: 28 / 28

Limted Warranty

Equipment manufactured by Roundup Food Equipment Division of A.J. Antunes & Co. has been constructed of the finest

materials available and manufactured to high quality standards. These units are warranted to be free from mechanical and

electrical defects for a period of two years from date of purchase or 30 months from shipment from factory, whichever occurs

first, under normal use and service, and when installed in accordance with manufacturer’s recommendations. To insure

continued proper operation of the units, follow the maintenance procedure outlined in the Owner’s Manual. During the first

12 months, all parts and non-overtime labor and travel expenses within a 100 mile/160 km, 2 hour round trip of the nearest

Authorized Service Center are covered; during the 13th to 24th month, parts only are covered (no labor or travel expense).

This warranty does not cover cost of installation, defects caused by improper storage or handling prior to placing

of the Equipment. This warranty does not include overtime charges or work done by unauthorized service agencies

or personnel. This warranty does not cover normal maintenance, calibration, or regular adjustments as specified

in operating and maintenance instructions of this manual, and/or labor involved in moving adjacent objects to gain

access to the equipment. This warranty does not cover consumable items such as platen release sheet and con-

veyor belt wraps. Travel time and mileage in excess of 2 hours (100 mile/160 km) from the nearest authorized service

agency is not covered under this warranty.

2. Roundup reserves the right to make changes in design or add any improvements on any product. The right is always reserved

to modify equipment because of factors beyond our control and government regulations. Changes to update equipment do

not constitute a warranty charge.

If shipment is damaged in transit, the purchaser should make a claim directly upon the carrier. Careful inspection should

be made of the shipment as soon as it arrives and visible damage should be noted upon the carrier’s receipt. Damage

should be reported to the carrier. This damage is not covered under this warranty.

4. Warranty charges do not include freight or foreign, excise, municipal or other sales or use taxes. All such freight and taxes

are the responsibility of the purchaser.

5. THIS WARRANTY IS EXCLUSIVE AND IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING

ANY IMPLIED WARRANTY OR MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, EACH OF WHICH IS

HEREBY EXPRESSLY DISCLAIMED. THE REMEDIES DESCRIBED ABOVE ARE EXCLUSIVE AND IN NO EVENT SHALL

ROUNDUP BE LIABLE FOR SPECIAL CONSEQUENTIAL OR INCIDENTAL DAMAGES FOR THE BREACH OR DELAY IN

PERFORMANCE OF THIS WARRANTY.

A.J. Antunes & Co.

Headquarters/Manufacturing

180 Kehoe Boulevard

Carol Stream, Illinois 60188 USA

Phone (630) 784-1000

Toll Free (800) 253-2991

Fax: (630) 784-1650

Antunes Equipment

Manufacturing (Suzhou) Ltd.,

9 Hou Ju Road, Building #24,

S&T Park, SND

Suzhou, Jiangsu, China 215011

Phone: 86-512-6841-3637

Fax: 86-512-6841-3907

www.ajantunes.com

Содержание Roundup VCT-2000





























Результаты поиска

Содержание Roundup VCT-2000

Отзывы:

Похожие инструкции для Roundup VCT-2000

Бренды по названию

Популярные бренды

Antunes Roundup VCT-2000, Руководство пользователя

Результаты поиска

Содержание Roundup VCT-2000

Отзывы:

Похожие инструкции для Roundup VCT-2000

Бренды по названию

Популярные бренды