Antunes Roundup VCT-2000 Скачать руководство пользователя страница 9

Страница: 9 / 28

VERTICAL CONTACT TOASTER

P/N 1010838 Rev. D 07/06

Burger King

TEMPERATURE CONTROL PANEL

NOTE: The term “set point temperature” refers to

the desired temperature setting.

To display the actual Platen temperature - providing it

is over 440° F (227° C), press the TEMP UP button.

To display the actual Auxiliary Air Heater temperature

- providing it is over 360°F (182°C), press the TEMP

DOWN button.

To switch the temperature display between Fahrenheit

(°F) and Celsius (°C), press and hold the TEMP

SCALE button for 5 seconds.

PLATEN HEATER TEMPERATURE ADJUSTMENT

1. Turn the Rocker Switch (power On/Off) to ON

and wait for the Temperature Display to finish the

power up sequence (Figure 4).

2. Press and hold both TEMP UP and TEMP DOWN

buttons for over 1 second until the display flashes

the Platen set point temperature, then release

(Figure 5).

3. Press the TEMP UP button to raise the set point

temperature or press the TEMP DOWN button to

lower the set point temperature.

NOTE: The Maximum Platen Set point Temperature

is 600

F. If no change in temperature is made

within 5 seconds, the display reverts back to the

previous set point.

4. Release the button when the desired set point is

displayed.

AUXILIARY AIR HEATER TEMPERATURE ADJUSTMENT

1. Turn the Rocker Switch (power On/Off) ON and

wait for Temperature Display to finish the power

up sequence (Figure 4).

2. Press and hold both TEMP UP and TEMP SCALE

buttons for over 1 second until the display flashes

the set point temperature, then release (Figure 6).

3. Press the TEMP UP button to raise the set point

temperature or press the TEMP DOWN button to

lower the set point temperature.

NOTE: The maximum Auxiliary Air Heater Set point

Temperature is 400

° F

4. Release the button when the desired set point is

displayed.

NOTE: If no change in temperature is made within

5 seconds, the display reverts back to the previous

set point.

TEMP

DOWN

TEMP

SCALE

˚F

˚C

POWER

TEMP

DOWN

TEMP

SCALE

˚F

˚C

POWER

SP - P

600

TEMP

DOWN

TEMP

SCALE

˚F

˚C

POWER

TEMP

DOWN

TEMP

SCALE

˚F

˚C

POWER

400

SP - A

FIGURE 4. TEMPERATURE POWER UP SEQUENCE

3. SP-A (Set point Auxiliary)

is displayed

1. SP-P (Set point Platen)

is displayed

“Heat On” LED will blink on/off during warm-up and when

either platen or auxiliary air heaters are calling for heat.

2. Current Platen Set point

Temperature setting is shown

4. Current Auxiliary Air Set

point Temperature is shown

5. “LO” is displayed until

platen temperature rises

above 550°F (288°C)

6. USE is displayed when

Platen Set point Temperature*

is reached

TEMP

DOWN

TEMP

SCALE

˚F

˚C

POWER

TEMP

DOWN

TEMP

SCALE

POWER

USE

* Platen set point temperature must be between

460°F (238°C) and 600°F (315°).

OPERATION (continued)

Содержание Roundup VCT-2000





























Результаты поиска

Содержание Roundup VCT-2000

Отзывы:

Похожие инструкции для Roundup VCT-2000

Бренды по названию

Популярные бренды

Antunes Roundup VCT-2000, Руководство пользователя

Результаты поиска

Содержание Roundup VCT-2000

Отзывы:

Похожие инструкции для Roundup VCT-2000

Бренды по названию

Популярные бренды