7
P/N 1011263 Rev. D 04/18
DAILY CLEANING
Clean the Toaster and Belt Wraps
1.
Turn the toaster’s power switch to
the off position. The toaster enters a
cool-down mode and will automati-
cally shut down when complete.
2.
Remove the top bun feeder (if
present), bun buffer frame and bun
feeder with heat-resistant gloves.
3.
Remove the front and rear conveyor
covers with heat resistant gloves.
4.
Inspect the front belts for any tears,
discoloration, or damage to the Belt
Wrap snaps. Replace any damaged
Belt Wrap as needed.
5.
If the front belts are in good condi-
tion, spray a clean, sanitizer-soaked
towel Sink Detergent solution. Wipe
the front belt clean. Rinse the front
belt with a separate clean, sanitizer-
soaked towel. Allow to air dry.
NOTE:
The belt rollers will continue
turning while in cool-down
mode. This allows you to clean
the entire belt. Only clean the
belts when they are in front of
the Backing Plate to avoid caus-
ing damage to the belts. Repeat
this step several times if there is
heavy carbon buildup on the con-
veyor belts.
6.
Inspect the rear belt for any tears,
discoloration, or damage to the Belt
Wrap snaps. Replace a damaged
Belt Wrap as needed. With proper
maintenance the Belt Wraps can six
months or longer.
7.
If the rear belt is in good condition,
spray a clean, sanitizer-soaked towel
with Sink Detergent solution. Wipe
the rear belt clean. Rinse the rear
belt with a separate clean, sanitizer-
soaked towel. Allow to air dry.
Figure 5. Bun Feeder
OPTIONAL TOP FEEDER
(PURCHASE SEPARATELY)
BUN FEEDER
NOTE:
The belt rollers continue turning
while in cool-down mode. This
allows you to the entire belt.
NOTE:
Only clean the belt when it is
in front of the Backing Plate to
avoid causing damage to the
belt.
8.
Wash, rinse, and sanitize the top bun
feeder (if present), bun buffer frame,
and bun feeder in the three-com-
partment sink.
9.
Wash, rinse, and sanitize the front
and rear conveyor covers in the
three-compartment sink.
10.
Reinstall the clean front and rear
conveyor covers.
11.
Reinstall the clean bun feeder. and
bun buffer frame.
12.
Clean the outside surfaces of the
toaster with clean, sanitizer-soaked
towel sprayed with an approved
degreaser. Rinse with a clean, sani-
tizer soaked towel and allow to air
dry.
13.
Place all used towels into the soiled
towel bucket.
Adjusting Toast Quality
When the unit is turned on and ready, you
can adjust the toast quality by pressing the
LEFT and RIGHT arrow buttons on the con-
trol panel. After making an adjustment, test
several products to verify they are toasting
at the desired quality.
NOTE:
This setting is maintained when
the unit is powered off.
NOTE:
If at any time the unit displays
an error message or if it fails to
operate properly, contact the fac-
tory immediately for service.
Belt is torn and folded.
Replace Belt.
Belt is missing snaps
and is damaged. Replace Belt.
Belt is damaged and folded.
Replace Belt.
Belt is folded and creased.
Replace Belt.
Содержание Gold Standard GST-5V
Страница 20: ...20 P N 1011263 Rev D 04 18 WIRING DIAGRAM ...
Страница 21: ...21 P N 1011263 Rev D 04 18 NOTES ...
Страница 22: ...22 P N 1011263 Rev D 04 18 NOTES ...
Страница 23: ...23 P N 1011263 Rev D 04 18 NOTES ...
