Antunes Gold Standard GST-5V, Руководство пользователя

Страница: 6 / 24

6 P/N 1011263 Rev. D 04/18
Language Selection
Follow these steps to set the language op-
tion for the GST-5V toaster.
1.
Plug in the power cord and turn the
toaster on.
2. See Figure 2. Press and hold the
MENU button for five seconds.
3. Press the LEFT ARROW button five
times so that the display shows
“English”.
4. Press the OK button.
5. Use the LEFT and RIGHT ARROW
buttons to select your preferred
language. The available
languages appear in the following
order:
• English
• Spanish
• French Canadian
• French
• German
• Portuguese
• Italian
• Swedish
• Russian
• Mandarin Chinese
• Japanese
6.
Press the OK button to save the
changes.
7. Return the toaster to service.
Figure 2. GST-5V Control Panel and Display
MENU
BUTTON
DISPLAY
OPERATING
INSTRUCTIONS
The GST-5V toasts Crowns, Heels, Clubs, and
other products. Follow these steps to start
the GST-5V:
1.
Turn on the toaster and wait for
warm-up to complete.
NOTE: The toaster fans turn on after
the A, B, or C Platen temperature
reaches 66°C (150°F).
2.
Set the Compression Knob to 4
(recommended). If you use setting
5, refer to Table 1 (page 8) for the
required internal settings.
3.
When the unit reaches operating
temperature, the control panel dis-
plays “Ready”.
4. Insert product into the designated
area of the Bun Feeder Assembly
with the cut side of the bun facing
towards the front. Toasted product
drops into the Bun Buffer.
Control Panel
The control panel (Figure 2) is located on
the right side of the unit. The LEDs on the
control panel light to signify when each
item is operating. The Service LED lights and
the corresponding LED (Motor, A Platen,
B Platen, C Platen) blinks when the unit
requires service. A message also appears on
the display.
Settings
Follow the steps below to view and adjust
the settings of the GST-5V.
1. When the unit is plugged in, press
and hold the MENU button (Figure
4) for five seconds. The control panel
displays “A Platen.” The display scrolls
to show the actual temperature, SSR
Duty cycle, and the setpoint.
Example: A Platen: 271°C 35% 271°C
NOTE: The unit does not have to be
turned on in order to access the
settings menu.
Factory Reset
To reset the unit to the factory default set-
tings, press and hold the LEFT and RIGHT
arrow buttons for 5 seconds until “Factory
Settings Restored” appears on the display.
NOTE: For ALL Units, this sets the dis-
play temperature to °C (Celsius).
Refer to the “Settings” section of
this manual to change the dis-
play temperature to °F (Fahren-
heit).
2. Use the LEFT and RIGHT arrow but-
tons (Figure 4) to scroll through the
settings, which appear in the follow-
ing order:
• A Platen
• B Platen
• C Platen
• Units (°C/°F)
• Buzzer (Soft, Loud, Mute)
• Display Languages
• ET (Elapsed Time)
• Controls Temperature
• Motor
3. To change a setting, press the OK
button and then use the LEFT and
RIGHT arrow buttons to adjust as
needed. Press the OK button again
to save the changes. See Figure 4.
NOTE: The Elapsed Time and Control
Temperature can not be adjust-
ed.
The table below describes the settings for
the A Platen, B Platen, C Platen, and Motor
depending on the Compression Knob set-
ting:
Compression
Setting #4
Compression
Setting #5
A Platen:
271°C (520°F)
A Platen:
275°C (527°F)
B Platen:
271°C (520°F)
B Platen:
275°C (527°F)
C Platen:
254°C (490°F)
C Platen:
255°C (491°F)
Motor: 4100 Motor: 4000