background image

11

Inspect with seasonal frequency  the wear status of the internal parts of the winch. In 

case of damaged parts, order the spare parts from Antal. 
To identify them, refer to the exploded view drawings at the end of this guide.

SPARE PARTS

Reassemble the winch following the steps of the maintenance sequence, in reverse 

order! In this manual you can also find the exploded view drawings of each model. In 

case of doubt, contact Antal at [email protected].

MOUNTING

VIDEO

Much more information on the Series of Antal XT winches is available in 

this video.

WARRANTY

Antal guarantees its equipment to be free of defects in material and workmanship for 3 

years from the date of purchase. 
During this period defective parts will be repaired or replaced by Antal. 
Warranty does not cover: products incorrectly installed; products used in applications 

for which they are not intended; products used under loads exceeding the product’s 

stated loads; products not properly maintained. 
Also, warranty does not cover defects due to corrosion, U-V degradation, and normal 

wear and tear.
Products subject to warranty claim will be returned to Antal for examination and possible 

repairing or replacement. Antal is not responsible for installation or shipping costs.

Содержание XT66/AL













Отзывы: