ANTAIRA LMP-0500 Series Скачать руководство пользователя страница 24

Страница: 24 / 78

Antaira Industrial Ethernet Switches

LMX-0500 Series User Manual V1.1

Terms

Value Description

Port No.

It shows each port status: Up for link active, and Down for link inactive.

Port Name

User can create or insert a value or label for each port’s identification

Status

Enable or disable a port

Speed/Duplex

User can set the bandwidth of each port as Auto-negotiation, 100 full,100

half,10 full,10 half mode.

Flow Control

Support symmetric and asymmetric mode to avoid packet loss when

congestion occurred.

Click “Apply” button to save changes.

Click to undo any changes made locally and revert to previously saved

values.

Figure 5.13 – Port Configuration Description

All manuals and user guides at all-guides.com

Содержание LMP-0500 Series















































































Результаты поиска

Содержание LMP-0500 Series

Отзывы:

Похожие инструкции для LMP-0500 Series

Бренды по названию

Популярные бренды

ANTAIRA LMP-0500 Series, Руководство пользователя

Результаты поиска

Содержание LMP-0500 Series

Отзывы:

Похожие инструкции для LMP-0500 Series

Бренды по названию

Популярные бренды