Ankom TDF28 Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 10

Ankom TDF28 Скачать руководство пользователя страница 8

In-Line Heater Replacement

(TDF28/28.1)

TDF

ANKOM Technology ● 2052 O’Neil Road ● Email: [email protected] ● Phone: 315-986-8090 ● Fax: 315-986-8091

Service procedure

TS018

Rev. B

6/04/2018

Page 8 of 10

29. Slide the black nut onto the In-Line

heater  cable  and  insert  the  cable
through  the  explosion  proof  ﬁIng  on
the underside of the Electrical Enclosure
on  the  right  side  (Below  HR  wire
connector).

28. Feed the black In-Line Heater cable up

the back of the instrument behind all
the cables, but in front of the green
tubing.

31. Use a cable <e to secure the black

In-Line  Heater  cable  to  the  gray  pump
motor  cable  as  it  was  earlier  on.
Carefully  cut  oﬀ  the  excess  from  the
cable <e.

32. Twist together one of the conductors

from  the  In-Line  Heater  cable  and  the
loose  blue  cable  in  a  clockwise  mo<on.
Then,  twist  the  combined  conductors
clockwise  into  the  yellow  wire  nut.
Gently  tug on  the  conductors  to  ensure
a secure connec<on.

30. Feed the cable through the explosion

proof  ﬁIng  un<l  the  black  insula<on
shows through the top about 1”. Ensure
that  the  nut  <ghtens  on  the  black
insula<on  so  it  does  not  damage  the
wire  itself.  Pull  the wire  gently  to make
sure it is secure.

«
...
6
7
8
9
10
»

Содержание TDF28











Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды